Rapid-Air SERVO FEED: 100C, 100D series - Manual (Page 15)

Pressing the F4 key at any time
returns you to the main menu.
MAIN MENU
F1=JOB # F2=MANUAL
F3=AUTOMATIC CYCLE
F4=REVIEW PARAMETERS
SELECT F2=MANUAL
In order to advance material into the
die, using the servo feed, the operator
has to be in the manual mode. Press-
ing the F2 on the keypad will cause
the screen to change to the manual
mode screen (see below). “Cycle rolls
with keys” - If the keypad has keys
with open rolls or close rolls on it then
the keys are active at this time and the
rolls can be electrically released for
inserting the material into the servo feed.
MANUAL MODE F1=INCH
F2=SINGLE FEED MODE
F4=EXIT MANUAL MODE
CYCLE ROLL WITH KEYS
F1=INCH MODE
Pressing the F1=INCH key will display
the following screen. Pressing and
holding the F2 and F3 key will command
the servo to move the material at a slow
rate of speed for the amount that was
entered for the feed length programmed
for the job number. You may press and
release the key as many times as you
wish to get the feed length.
JOG: TYPE=JOG-LENGTH
F1=ALTER TYPE OF JOG
F2=FWD F3=REV
F4=EXIT (MANUAL MODE)
F1=ALTER TYPE OF JOG
Pressing the F1=alter type of jog will
allow the operator to change the
Operator Input Terminal – Programming Procedure – Standard Software
current “jog to length” to “continuous”.
See below. Pressing and holding the
F2 and F3 key will command the servo
to move the material at a slow rate of
speed for as long as the key
is pressed.
JOG: TYPE=CONTINUOUS
F1=ALTER TYPE OF JOG
F2=FWD F3=REV
F4=EXIT (MANUAL MODE)
Pressing the F4 key once will
reset the program to the manual
mode screen.
MANUAL MODE F1=INCH
F2=SINGLE FEED MODE
F4=EXIT MANUAL MODE
CYCLE ROLL WITH KEYS
F2-SINGLE FEED
If the operator presses F2 then the
following screen is displayed. The
single feed mode is active and every
time the F1 key is pressed then the
feed will cycle and move the distance
indicated on the feed length line.
SINGLE FEED MODE
FEED LENGTH=XXX.XXX
F1=FEED SINGLE LNGTH
F4=EXIT (MANUAL MODE)
Pressing F4 once resets the program
to the manual mode display. Pressing
the F4 key twice resets the program
to the main menu display. If the F4
key was pressed twice the following
screen is displayed.
MAIN MENU
F1=JOB # F2=MANUAL
F3=AUTOMATIC CYCLE
F4=REVIEW PARAMETERS
F3=AUTOMATIC CYCLE
If the feed has been properly set up
and tested in manual and the press
has been electrically interlocked
with the feed, feed and pilot switches
wired to the correct terminals, then
pressing the F3 key will display the
following screen.
SELECT CONTINUOUS OR
BATCH CYCLE F1=BATCH
F2=CONTINUOUS CYCLE
F4=EXIT TO MAIN MENU
F2=CONTINUOUS
If the F2 key was pressed then the
servo will be in the auto total mode
and the following screen appears.
AUTOMATIC TOTAL=000000
JOB #=XX PILOTS=NO
LGTH=XXX.XXX SPM=XXX
SPEED=XXX% F4=RETURN
Pressing the F4 key, stops the
automatic cycle and the main menu
screen appears.
MAIN MENU
F1=JOB # F2=MANUAL
F3=AUTOMATIC CYCLE
F4=REVIEW PARAMETERS
F3=AUTOMATIC CYCLE
If the feed has been properly set up
and tested in manual and the press
has been electrically interlocked
with the feed, feed and pilot switches
wired to the correct terminals, then
pressing the F3 key will display the
following screen.
SELECT CONTINUOUS OR
BATCH CYCLE F1=BATCH
F2-CONTINUOUS CYCLE
F4=EXIT TO MAIN MENU
F1=BATCH
PROGRAmmING PROCEDURE – (CONTINUED)