Rapid-Air SMART MINI-SERVO FEED CUT-TO-LENGTH: SMS2, SMS4, SMS8 - Manual (Page 12)

Programming Procedure
(continued)
A VALID JOB # MUST
BE ACTIVE TO GO ON
GO TO JOB ENTER SCRN
JOB SCRN F6=EXIT
SECTION 2 F2 - MANUAL MODE
Pressing F2, manual mode while on
the “MAIN MENU”, will cause the
following the screen.
EXIT
MANUAL MODE
INCh FEED SGL
MODE LENGTh
F1, inch mode, produces the following:
EXIT
SELECT JOG MODE
CONTINUOUS INCh 1
JOG LENGTh
F3, feed sgl length, produces the fol-
lowing:
EXIT
JOB 00 LENGTh = 00.000
FEED 1 SINGLE
LENGTh CUT CYCLE
F6, exit, in both screens moves the
display back to “MANUAL MODE”.
F1, inch mode, give the operator two
additional choices. These are:
F1, Continuous jog
EXIT
CONTINUOUS JOG:
USE X kEYS TO
JOG + OR -
F3, inch 1 length
EXIT
FEED 1 LENGTh JOG:
USE X kEY TO INCh
FORwARD ONE LENGTh
F6, exit, in both screens moves the
display up one level to “MANUAL
MODE”. F1, Continuous jog, allows
an operator to jog each axis in either
direction. The X-axis keys move the
feed axis.
F3, inch 1 length, allows an operator
to inch the material forward one feed
length. The “X” axis keys will move
the axis while a key is pressed until
one feed length is reached. If the key
is released before one feed length is
reached, the axis will stop and wait
until the jog key is pressed again or
one feed length is reached.
SECTION 3 F3 - AUTOMATIC MODE
Pressing F3, automatic mode while
on the “MAIN MENU”, will cause the
following the screen.
EXIT
AUTOMATIC MENU:
BATCh AUTO
MODE MODE
F1, batch mode, controls batches from
the “BATCH START” screen.
EXIT
BATCh SIZE = 000000
BATCh COUNT = 000000
ST_CYC SET_CNT CONT
The F1 key, ST_CYC (start cycle), will
begin the feed/cut cycle. The “BATCH
MENU” screen appears as follows.
CURRENT TOTAL = 000000
BATCh SIZE = 000000
JOB # =00 % SPEED = 000
LGhT = 00.000 F6 = EXIT
The F2 key, SET_CNT (set count), will
allow the operator to set the batch
size or change the batch size. The
“BATCH SET” screen is:
INPUT A BATCh SIZE
BATCh SIZE = 000000
START
CYCLE F6 = EXIT
The F3 key, CONT (continue), will re-
start a batch stopped before reaching
the full batch size by exiting with the
F6 key. The “BATCH MENU” screen is:
BATCh TOTAL = 000000
BATCh SIZE = 000000
JOB#=00 SPM = 000
BLANk = 00.000 F6 = EXIT
NOTE: If the batch size is set to
000000, the “BATCH SET” screen will
appear. The “BATCH SET” screen will
allow an operator to set the batch
count. The “BATCH SET” screen can
also be found under ramp/count se-
lection on the “MAIN MENU” screen.
The “BATCH SET” screen is shown
above under F2. After the batch size
is entered and F1 (start cycle) is
pressed, the program will return to
“BATCH SET” screen.
When the batch total equals the
batch size, the feed will stop and will
display this screen.
EXIT
BATCh CYCLE COMPLETE
BATCh COUNT = 000000
NEw CYCLE
F6, exit, will return to the “MAIN
MENU” screen. F1, start new cycle,
will reset the batch count total to 000000
and will start feeding another batch.
Depressing F3, auto mode, while on the
“AUTOMATIC MODE” screen will display:
EXIT
AUTO TOTAL = 000000
JOB # =00 LENGT = 00.000
CUT = 000 SPEED = 000 %
The automatic cycle will continue
until the F6 key, exit, is pressed.