Lincoln Electric IMT10097 POWER MIG 216 - Manual (Page 20)

C-1 C-1 ACCESSORIES
DRIVE ROLL KITS
Refer to Table C.1 for various drive roll kits that are
available for the POWER MIG® 216.The item in Bold
is supplied standard with the POWER MIG® 216.
TABLE C.1
DUAL CYLINDER MOUNTING KIT
(K1702-1)
Permits stable side-by-side mounting of two full size
228.6mm dia x 1.524m high(9" dia. x 5' high) gas
cylinders with “no lift” loading. Simple installation and
easy instructions provided. Includes upper and lower
cylinder supports, wheel axles and mounting hard-
ware.
SMALL SPOOL SPINDLE ADAPTER
(K468)
The K468 spindle adapter allows the use of 8" diame-
ter small spools.
SPINDLE ADAPTER FOR 14 LBS.
COILS (K435)
The K435 spindle adapter allows 14lbs. (6kg.)
Innershield Coils to be mounted on 2” (51mm) O.D.
spindle.
ALTERNATIVE MAGNUM GMAW
GUN AND CABLE ASSEMBLIES
The following Magnum Pro 250L gun and cable
assemblies are separately available for use with the
POWER MIG® 216. Each is rated at 250 amps 40%
duty cycle and is equipped with the integrated connec-
tor, twist-lock trigger connector, fixed nozzle and insu-
lator, and includes a liner, diffuser, and contact tips for
the wire sizes specified:
• Unplug or Disconnect all input power
from the POWER MIG® 216 before
installing the Spool Gun and Kit.
------------------------------------------------------------------------
MAGNUM GUN CONNECTION KIT
(K466-6)
Using the optional K466-6 Magnum Connection kit for
the POWER MIG® 216 permits use of standard
Magnum 200, 300 or 400 gun and cable assemblies.
OPTIONAL SPOOL GUNS AND
ADAPTERS
The POWER MIG® 216 is capable of operating with the
following optional spool guns:
Spool gun Adapter (K2703-1)
This kit is designed to allow the Magnum SG or Magnum
250LX spool gun to operate with the POWER MIG® 216.
The kit includes the gas solenoid, gas lines, wiring harness
and gun connection panel. The gun connection panel fea-
tures a 6 pin ms-type connector for the Magnum SG spool
gun and a 7 pin ms-type connector for the Magnum 250LX
spool gun and a selector switch to choose which gun you
are using.
NOTE: The K2703-1 spool gun adapter disables the
Magnum 100SG capability.
Wire Size Drive Roll Kit
.023”-.030” (0.6-0.8 mm) KP1696-030S
.035” (0.9 mm) KP1696-035S
Solid
.045” (1.1 mm) KP1696-045S
Steel
.035”-.045” (0.9-1.1mm) KP1696-1
.040” (1.0mm) KP1696-2
Cored
.035” (0.9 mm) KP1697-035C
.045” (1.1 mm) KP1697-045C
Aluminum 3/64” (1.2 mm) KP1695-3/64A
English Wire Metric Wire
Length Part No. Size Size
10' (3.0 m)
12' (3.6 m) KP42-4045-15 .035” – .045"
0.9 – 1.1 mm
15' (4.5 m)
WARNING
SPOOL GUN
Magnum 100SG
(K2532-1)
Magnum SG
(K487-25)
Magnum 250LX
(K2490-1)
ADAPTER
Factory Ready
No Adapter Required
Spool Gun Adapter
K2703-1
RATING
Light Duty
130amp 30% Duty Cycle
Medium Duty
250Amp 60% Duty Cycle
Heavy Duty
300 Amp 60% Duty Cycle
POWER MIG® 216