Superwinch X9 – 4,082 kgs/12V (1901, 1902) - Manual (Page 7)

6. EQUIPPING THE WINCH WITH A
ROLLER FAIRLEAD will substantially
reduce wear on the wire rope
during angle pulls (Figure 16).
The rollers eliminate heavy rub-
bing and abrasion to the wire rope.
Periodically check tightness of
mounting bolts and electrical con-
nections. Remove any dirt or corro-
sion that may have accumulated on
the electrical connections.
Repairs should be done by
Authorized Superwinch Repair
Centers ONLY. Do not attempt
to disassemble the gearbox.
Disassembly will void warranty.
LUBRICATION
The gearbox and drum bearing are
permanently lubricated with a high
performance gear lube. If relubrica-
tion is necessary (after repair or
disassembly) only use factory
approved grease (Superwinch
Part No. 90-15020).
REPLACING THE WIRE ROPE
Never substitute a heavier or lighter
wire rope. Never use rope made of
any other material other than wire.
Always replace damaged wire
rope with manufacturer’s identi-
cal replacement part (see
Replacement Parts list). Pass attach-
ing end of wire rope through the
fairlead (if equipped) and attach it
to the drum. When inserting the
wire rope into the drum, insert it
into the correct end of the hole
provided (Figure 17). Tighten the
set screw securely.
It is important that the wire rope
be wound tightly onto the drum. A
good way to do this is to attach the
wire rope hook to a fixed object at
the top of a slight incline, then
winch the vehicle up the incline.
12 13
TIPS FOR EXTENDING THE LIFE OF
THE WINCH
1. KEEP A TIGHTLY WOUND WIRE
ROPE DRUM. Do not allow the
wire rope to become loosely
wound. A loosely-wound drum
allows a wire rope under load to
work its way down into the layers
of wire rope on the drum. When
this happens, the wire rope may
become wedged within the body
of the windings damaging the
wire rope. To prevent this prob-
lem, keep the wire rope tightly
and evenly wound on the drum at
all times. A good practice is to
rewind the wire rope under ten-
sion after each use. One way to
do this is to attach the hook to a
stationary object at the top of a
gradual incline and winch your
vehicle up the incline.
2. DO NOT ALLOW WINCH MOTOR
TO OVERHEAT. Remember, the
winch is for intermittent use only.
During long or heavy pulls the
motor will get hot. The internal
parts will be hotter than the case.
To check the motor temperature,
stop winching and carefully touch
the motor case, if the motor is
uncomfortable to touch, allow
the motor to cool before continu-
ing. KEEP THE ENGINE RUNNING
TO RECHARGE THE BATTERY dur-
ing this break.
3. To maximize winch and wire rope
life, use a pulley block to double
line heavier loads (Figure 14).
4. The pull required to start a load
moving is often much greater
than the pull required to keep it
moving. AVOID FREQUENT STOP-
PING AND STARTING during pull.
5. PREVENT KINKS BEFORE THEY
OCCUR.
Figure 14
M A I N T E N A N C E
Figure 15
a
b
c
a. This is the start
of a kink. Wire
rope should be
straightened.
b. Wire rope was
pulled and loop
has tightened into
a kink. Wire rope
is now permanent-
ly damaged and
must be replaced.
c. Result of kink-
ing is that each
strand pulls a dif-
ferent amount caus-
ing strands under
greatest tension
to break and
reduce load capac-
ity of wire rope.
The wire rope
must be replaced.
Figure 16
Figure 17
Figure 18
HANDHELD REMOTE
DIRECTIONAL SWITCH
(Spring to Center)
HANDHELD REMOTE
DIRECTIONAL SWITCH
(Rope-In Position)
HANDHELD REMOTE
DIRECTIONAL SWITCH
(Rope-Out Position)
BLUE BLUE BLUE YELLOW YELLOW YELLOW
BLACK
GROUND
BLACK
GROUND
BLACK
GROUND
RED RED RED
WHITE WHITE WHITE
BLACK BLACK BLACK MOTOR MOTOR MOTOR
FIELD WINDINGS FIELD WINDINGS FIELD WINDINGS
OFF WIRE ROPE IN WIRE ROPE OUT
BLUE BLUE BLUE YELLOW YELLOW YELLOW
RED RED RED