Rivers Edge RE712 14' PERIMETER - Manual (Page 6)

TREESTANDS
14' Perimeter ™ Ladder Pod (RE712)
Page 6
HuntRiversEdge.com
HuntRiversEdge.com
800-450-EDGE (3343)
c.Locate the (4) 48” male cross braces (TP150) and (4) 60” female cross
braces (TP131). Insert the male cross braces into the female cross braces.
Using (4) provided 1/4-20 x 1-1/4” bolts and locknuts, secure these cross
braces in the hole location listed for pole lengths D & e (two each).
SEE
FIGURE 8.
19. a. The two cross braces that run diagonally from the top ladder section to
the top/middle leg joint are the shortest. Using pole length A (approximately
67”), attach to the support brace tabs on top ladder section using (2)
provided 5/16-18 x 3/4” bolts and locknuts. Attach other end of cross brace
assemblies to the support brace tabs of top/middle leg joints using (2)
provided 5/16-18 x 1-1/4” bolts and locknuts.
SEE FIGURE 8 & 9.
IMPORTANT NOTE: Be sure to use 1-1/4” bolts at any location where
multiple cross brace poles are attached.
b. The two cross brace poles that run diagonally from the top/middle leg
joint to the middle/bottom ladder joint are longest. Using pole length e
(approximately 99-3/4”) attach to the support brace tabs of leg joints and
ladder joints using (2) provided 5/16-18 x 3/4” bolts, (2) provided 5/16-18
x 1-1/4” bolts and (8) locknuts.
SEE FIGURE 8 & 9.
NOTE: You will use the 1-1/4” bolts and nuts to attach cross braces
at the leg joint that is already holding the diagonal braces.
IMPORTANT NOTE: Be sure to use 1-1/4” bolts at any location where
multiple cross brace poles are attached.
c. The two cross brace poles that run from the top/middle ladder joint to
the middle/bottom leg joint are pole length D (approximately 92-3/4”).
Using pole length D attach to the support brace tabs of leg joints and
FIGURE 9
ladder joints using (4) provided 5/16-18 x 3/4” bolts and (4)
locknuts.
SEE FIGURE 8 & 9.
d. The two cross braces that run diagonally between both rear
legs are both the same length. Using pole length C (approximately
91-1/8”), attach to the support brace tabs on leg joints using (4)
provided 5/16-18 x 3/4” bolts and locknuts.
SEE FIGURE 8 &
9.
20. Once all cross braces are attached to pod, you must now tighten
all nut & bolt assemblies. Be sure not to over tighten or crush
tubing when tightening! Double and triple check all nuts and
bolts to make sure all are securely fastened.
21. Go over every detailed step of assembly to be sure all assembly
is done correctly and all bolt locations are secured and snug.
Be sure not to over tighten or crush tubing when tightening!
Once you are certain all assembly is complete and correct,
proceed to uprighting instructions.
A (approx. 67")
5/16-18 x 3/4" bolts
D (approx. 92-3/4")
5/16-18 x 1-1/4" bolts where more
than one cross brace pole bolts to
support brace tabs A (approx. 67")
D (approx. 92-3/4")
e (approx. 99-3/4")
e (approx. 99-3/4")
C (approx. 91-1/8")
C (approx. 91-1/8")
View of pod lying on ground
between one leg section and
ladder section.