beautypg.com

Service level, Replacement – Ransburg 9040 Classic Power Supply _NO2 Gun 76657-14, -142 User Manual

Page 24

background image

CP-97-03.6

9040 Classic for the No. 2 Process Handgun - Maintenance

2 0

2 0

2 0

2 0

2 0

SERVICE LEVEL

SERVICE LEVEL

SERVICE LEVEL

SERVICE LEVEL

SERVICE LEVEL

Personnel who service this unit must be quali-
fied electronics technicians. Replacement parts
are designed to be made at the assembly level.
See "Parts Identification" section of this manual
for part numbers and ordering information.

!

ALWAYS

ALWAYS

ALWAYS

ALWAYS

ALWAYS turn power to the power

supply OFF

OFF

OFF

OFF

OFF, unplug the electrical cord from

its outlet, remove the front panel fuse, and
lock the power supply out before making
repairs or replacements.

W A R N I N G

W A R N I N G

W A R N I N G

W A R N I N G

W A R N I N G

!!!!!

!

DO NOT

DO NOT

DO NOT

DO NOT

DO NOT attempt to make repairs to

the printed circuit board!

!

DO NOT

DO NOT

DO NOT

DO NOT

DO NOT attempt to make repairs

beyond those described. All others should
be made ONLY

ONLY

ONLY

ONLY

ONLY by Ransburg service

personnel.

C A U T I O N

C A U T I O N

C A U T I O N

C A U T I O N

C A U T I O N

!!!!!

REPLACEMENT

REPLACEMENT

REPLACEMENT

REPLACEMENT

REPLACEMENT

PROCEDURES

PROCEDURES

PROCEDURES

PROCEDURES

PROCEDURES

Before making replacements, check for defec-
tive wiring or connections between the affected
components. If there is a broken wire, defective
insulation, or dirty, loose or corroded connec-
tions, repair or replace them before going to the
expense of replacing a component.

Front Panel Fuse 1FU

Front Panel Fuse 1FU

Front Panel Fuse 1FU

Front Panel Fuse 1FU

Front Panel Fuse 1FU

1.

Insert screwdriver into slot in front panel
fuse holder, push in, and rotate counter-
clockwise.

2.

Remove screwdriver and fuse holder will
slide out.

3.

Remove fuse from fuse holder and re-
place with new fuse (see "Parts Identifi-
cation" section of this manual for part
numbers).

4.

Insert fuse holder back into front panel
and with a slight inward pressure, rotate
screwdriver clockwise until it locks into
place.

PC

PC

PC

PC

PC Board Fuse F2

Board Fuse F2

Board Fuse F2

Board Fuse F2

Board Fuse F2

----- REFER TO FIGURE 7 FOR FUSE

REFER TO FIGURE 7 FOR FUSE

REFER TO FIGURE 7 FOR FUSE

REFER TO FIGURE 7 FOR FUSE

REFER TO FIGURE 7 FOR FUSE
L O C A T I O N

L O C A T I O N

L O C A T I O N

L O C A T I O N

L O C A T I O N

1.

Ensure power supply is unplugged from
AC outlet and open cabinet door.

2.

Replace defective fuse (see "Parts Iden-
tification" section of this manual for part
numbers).

3.

Secure cabinet door and plug power
supply back in.

ON/OFF Switch 1SW

ON/OFF Switch 1SW

ON/OFF Switch 1SW

ON/OFF Switch 1SW

ON/OFF Switch 1SW

1.

Ensure power supply is unplugged from
AC outlet and open the cabinet door.

!

A spare F2 PC board fuse, included

from the factory, is located in the lower
right hand corner inside the cabinet door.

N O T E

N O T E

N O T E

N O T E

N O T E

2.

Remove the four quick connect termi-
nals from the rear of ON/OFF switch
1SW.

!

ALWAYS

ALWAYS

ALWAYS

ALWAYS

ALWAYS double check that the power

supply is unplugged from its AC outlet
before working with any internal wiring.

W A R N I N G

W A R N I N G

W A R N I N G

W A R N I N G

W A R N I N G

!!!!!

3.

Press panel retaining clips on top and
bottom of switch 1SW together and push
switch out of panel from the inside.

!

It is recommended that the four ON/

OFF switch wires be tagged with their re-
spective terminal connections to 1SW be-
fore removing.

N O T E

N O T E

N O T E

N O T E

N O T E