Kasco Marine LED6125 - Manual (Page 2)

2
THANKS
We at Kasco Marine, Inc. would like to both thank and
congratulate you on your purchase of the Submersible
LED Light Kit. This kit will illuminate your fountain
for a beautiful display. We thank you for choosing
Kasco for your fountain and aeration needs and want
you to be completely satisfied with your purchase.
Important Safety
Please read and follow these extremely important
safety and handling instructions for your Kasco equip-
ment. Following these instructions will help ensure
your safety and the quality performance of your equip-
ment.
• Under NO circumstances should anyone enter
the water with the electrical equipment plugged
in and/or in operation. All Kasco equipment is
designed and built for use in water, and control
panels are available with GFCI protection. How-
ever, it is NEVER recommended to enter the water
with the equipment in operation.
• Kasco’s Submersible Light Kits are intended for
use with a Listed control panel having a GFCI
protected receptacle, or field wiring terminals and
disconnect switch, or a timer with a disconnect for
use with a GFCI receptacle. They are intended
to be mounted on a floating fountain or aerator
for use in a natural or man-made body of water to
comply with NEC Article 682.
• Kasco’s Submersible Light Kits have not been
evaluated for use in swimming pools, spas or sta-
tionary fountains.
• The power connection for the light kit is 120Vac
and MUST be plugged into a GFCI protected
receptacle or GFCI protected field terminal con-
nections.
• Caution should be used when dealing with any
electrical and/or moving equipment.
• NEVER run the unit out of water. It could create a
dangerous situation for the operator.
• Extreme caution should be used around water, es-
pecially cold water, as in Spring, Fall, and Winter,
which poses a hazard itself.
• NEVER lift or drag the fountain or light kit by the
power cords. If you need to pull the unit to the
side of the pond, use the anchoring ropes.
• Do not use waders in ponds/lakes that are deep,
with drop-offs, drastic slopes, or soft bottom mate-
rial.
• Do not use a canoe or boat that tips easily during
installation
• To reduce the risk of electrical shock, be certain
the light kit is connected to the GFCI protected
lighting circuit of your control panel. For more
information regarding your control panel instruc-
tions, refer to your fountain owner’s manual or
download control panel wiring diagrams from
http://kascomarine.com/instructions.html. A con-
trol panel must be installed a minimum of 5 feet
(3m in Canada) from the body of water unless
separated from the body of water by a fence, wall,
or other permanent barrier that will make the unit
inaccessible to persons in the water.
General Instructions
INSPECT THE SHIPMENT
Immediately inspect this shipment for any visible
damages. Also cross reference the “Parts Included”
section to check for part shortages. Shortages should
be reported immediately to your Kasco Marine distrib-
utor or representative and damages reported to your
carrier and Kasco Marine.
Parts Included
LED3125
• A. Light Kit cord with waterproof connectors (1)
• B. Sealed LED light fixtures with flex sleeve (3)
• C. 1/4” x 1 3/8” Stainless Steel Bolts (3)
• D. 1/4” Stainless Steel Flat Washer (3)
• E. 1/4” Stainless Steel Lock Washer (3)
• F. 1/4” Stainless Steel Nut (3)
• G. Nylon Cable Ties (9)
• H. Stainless steel mounting brackets & hardware (3)
• I. Sealing cap (3)
• J. 4” spacer washers (3)
• K. 1/4” x 5” Stainless Steel Bolts (3)
• L. Spare Oring (1)
• M. Rubber caps (3)
• N. Colored lenses (20 - 4 of each color)
Note: Extra hardware may be included. One extra
spare oring is included. One extra lens of each color is
included.