Server CSP-EZ (94160/94150) - Manual (Page 8)

GENERAL SERVICE, REPAIR,
OR RETURNS
Before sending any item to Server Products for service,
repair, or return, contact Server Products customer
service to request a Return Authorization Number.
Merchandise must be sent to Server Products with this
number.
Merchandise being returned for credit must be in new
and unused condition and not more than 90 days old
and will be subject to a 20% (percent) restocking
charge. Electrical parts (thermostats, heating elements
etc.) are not returnable.
Server Products maintains a fully staffed service depart-
ment with highly skilled factory trained personnel.
Service is extremely prompt. Under normal circum-
stances, a repaired unit is shipped out the day after it is
received. Labor charges are reasonable.
SERVICE
Contact your dealer or Server Products Inc.
customer service department for the following:
ORDERING REPLACEMENT PARTS
Be prepared to give this information:
• Model Letters/Name/Numbers
• Part Numbers- P/N
• Series Numbers/Letters
• Part Description
This information and other important data is stamped
on the lid or cylinder of pumps or on the bottom or
back side of every unit.
SERVER PRODUCTS
LIMITED WARRANTY
All Server Products equipment is backed by a
two-year limited warranty against defects in materials
and workmanship. For complete warranty information
go to: www.server-products.com

Server Products Inc.
3601 Pleasant Hill Road
Richfield, WI 53076 USA

262.628.5600

800.558.8722

262.628.5110

[email protected]

www.server-products.com
NSF International listed.
UNIT CLEANING
BEFORE FIRST USE AND AFTER USE DAILY,
DISASSEMBLE AND CLEAN UNIT AND PUMP. STAINLESS
STEEL PARTS CAN CORRODE. IT IS IMPORTANT TO
CLEAN, RINSE, SANITIZE, AND DRY THESE PARTS DAILY
AND PROPERLY. FAILURE TO COMPLY WITH ANY OF
THESE INSTRUCTIONS MAY VOID UNIT WARRANTY.
1 SEE UNIT TAKE DOWN, PUMP DISASSEMBLY, AND
PUMP CLEANING.
2 ENSURE UNIT IS “OFF” AND UNPLUGGED.
C
E
Warning- Electrical shock could occur:
• Electrical components of unit could be
damaged from water exposure or any liquid.
• Never immerse unit into water or any liquid.
• Never use any water jet or pressure sprayer
on unit.
3 WASH PRODUCT VESSEL AND PUMP WITH
DISHWASHING DETERGENT AND HOT WATER DAILY.
RINSE THOROUGHLY AND DRY WITH A CLEAN SOFT
CLOTH.
• A general purpose, nonabrasive cleaner may be
used on hard to remove food deposits.
• A mildly abrasive NYLON or brass brush may be
used to remove any stubborn food or mineral
depositson interior surfaces of unit.
• Do not use abrasive cleansers, scrapers,
steel pads, steel wool, or other cleaning tools
that can scratch surfaces.
• Do not use cleansing agents with high
concentrations of acid, alkaline or chlorine.
These agents can corrode stainless steel.
• Fully rinsing all parts can help prevent corrosion.
• Various elements and minerals, such as chlorides
in tap water, can accumulate on stainless steel
parts and create corrosion.
• To prevent corrosion on any stainless steel parts,
it is important to fully dry with a clean soft cloth
regularly.
4 WIPE EXTERNAL SURFACES OF UNIT DAILY WITH
A CLEAN DAMP CLOTH. DRY WITH A CLEAN SOFT
CLOTH.
• A nontoxic glass cleaner may be used for cleaning
any stainless steel parts.
5 SANITIZE ALL PARTS FOLLOWING LOCAL
SANITIZATION REQUIREMENTS. ALL PARTS IN
CONTACT WITH FOOD MUST BE SANITIZED.
• Allow parts to fully air dry after sanitization.
• Fully air drying all parts will prevent condensation
from developing between food vessel and unit
basin.
Plastic Lid, Plastic Cover, Plastic Top and
Plastic Chiller Block Insulation Assembly:
• Not dishwasher safe.
• Hand Wash Only.
Do not place plastic lid, plastic cover, plastic top or plastic
chiller block insulation assembly under, in, or near to high
heat, as this can melt the plastic.