Pach and Company AeGIS 4000BP Manual - Manual (Page 21)

71-72
AUTOMATIC OR
MANUAL CALL
FORWARDING
SEE FUNCTION
CODES 87, 88
AND 89 IF YOU
WANT TO SET
THE SYSTEM
FOR
AUTOMATIC
CALL
FORWARDING.
SEE ENABLE
MANUAL CALL
FORWARDING
ON CHAPTER 6
IF YOU WANT
TO SET THE
SYSTEM FOR
MANUAL CALL
FORWARDING.
Step 1 Pick up the phone and wait
for a dial tone.
Step 2 Press # # and you will hear
“One Short Beep”.
Step 3 Press # and you will hear
“One Short Beep”.
Step 4 Enter the Function Code
number “71” or “72” then press #, you
will hear “No Beep”. If you hear
“Two Long Beeps”, a phone number
is already programmed. Press
∗, you
will hear “One Short Beep” and
select another Function Number
(71 – 72).
Step 5 Enter a phone number up to
11-digit.
Step 6 Enter another function code
to program a different parameter or
exit the program by pressing
∗ ∗ and
you will hear “Three Short Beeps” .
Step 1 Entering The Programming
Mode: Press 0 and # simultaneously
then release. If you are in the
programming mode, proceed to step 2.
Step 2 Enter the 4-digit Master
Code (factory default is 0000) and you
will hear “One Short Beep”. If you
entered an invalid master code you will
hear “One Long Beep”, repeat
step 1. Should your master code
become lost or forgotten see Reset
Master Code.
Step 3 Enter Function Number
(71 – 72) then #, you will hear “Two
Long Beeps”. If you hear “No Beep”,
a phone number is already
programmed. Press
∗, you will hear
Step 1 Pick up the phone and wait
for a dial tone.
Step 2 Press # # and you will hear
“One Short Beep”.
Step 3 Press # and you will hear
“One Short Beep”.
Step 4 Enter the Function Code
number “71” or “72” then press #, you
will hear “No Beep”. If you hear “Two
Long Beeps”, a phone number is
already programmed. Press
∗, you will
hear “One Short Beep” and select
another Function Number (71 – 72).
Step 5 Enter the a phone number
up to 11-digit.
Step 6 Enter another function code
to program a different parameter or
exit the program by pressing
∗ ∗ and
you will hear “Three Short Beeps”.
Step 1 Pick up the phone and wait
for a dial tone.
Step 2 Press # # and you will hear
“One Short Beep”.
Step 3 Press # and you will hear
“One Short Beep”.
Step 4 Enter the Function Code or
index number “71” or “72” then press
#, you will hear “Two Long Beeps”;
means the a phone number is already
programmed, proceed to step 5. If you
hear “No Beep”, means no phone
number is programmed, press
∗ and
continue step 4 or proceed to step 6.
• “One Long Beep”, the master code
is rejected and the connection will be
disconnected.
Step 3 Press 6, you will hear
“Three Short Beeps” and the system
disconnects the call.
Step 1 Call to the AeGIS 4000BP
system (you must know the system’s
phone number), you will hear: “One
Short Beep”, the gate is locked. “Two
Short Beeps”, the gate is unlocked.
Step 2 Press # then enter a valid
master code and you will hear:
• “One Short Beep”, the master code
is accepted then press # and you will
hear “One Short Beep”.
• “One Long Beep”, the master code
is rejected and the connection will be
disconnected.
Step 3 Press # to enter into the pro-
gramming mode and you will hear
“One Short Beep” or
∗∗ to hang-up
the call.
Step 4 Enter the Function Code or
index number “71” or “72” then press
#, you will hear “No Beep”. If you
hear “Two Long Beeps”, a phone
number is already programmed. Press
∗, you will hear “One Short Beep”
and select another Function Number
(71 – 72).
Step 5 Enter a phone number up to
11-digit.
Step 6 Enter another function code
to program a different parameter or
exit the program by pressing
∗ ∗ and
you will hear “Three Short Beeps”.
Call to the AeGIS 4000BP system (you
must know the system’s phone
number), you will hear: “One Short
Beep”, the gate is locked. “Two Short
Beeps”, the gate is unlocked.
Step 2 Press # then enter a valid
master code and you will hear:
• “One Short Beep”, the master code
is accepted then press # and you will
hear “One Short Beep”.
• “One Long Beep”, the master code
is rejected and the connection will be
disconnected.
Step 3 Press # to enter into the
programming mode and you will hear
“One Short Beep” and proceed to
step 4 or
∗∗ to hang-up the call.
Function Local Programming Premise Phone Remote Phone
Program
Automatic or
Manual call
forwarding
Delete or
Rewrite
Automatic or
Manual call
forwarding
Pach and Company Page 13
AeGIS 4000BP Chapter 3. Programming