Alcatel-Lucent 1850 TSS-160 - Manual (Page 3)

Alcatel-Lucent 1850 TSS-160 | Release 3 | Data Sheet 3
Ethernet forwarding criteria
• Port
• Port plus MAC
• Port plus VLAN
• Port plus MAC plus VLAN
• Port plus MAC plus VLAN plus
prio bits
• Unicast traffic
• Multicast traffic
• Broadcast traffic
IGMP functionality
• Internet Group Management
Protocol (IGMP) snooping
• IGMP proxy
• IGMP fast leave
ATM functionality
• Pseudo-wire emulation edge to
edge (PWE3): ATM-PWE3 gateway
• OC-3/STM-1 ATM unchannalized
• ATM virtual path identifier/virtual
channel identifier (VPI/VCI)
N:1 mapping with PWE3 static
configuration
• ATM QoS, OAM F4, F5: PWE OAM
T-MPLS functionality
• Data plane: T-MPLS, MPLS
• T-MPLS OAM: CV, automatic pro-
tection switching (ApS), forward
defect indication (FDi)
• Tunnel Lin Protection 1:1
• Ethernet line (E-line), E-LAN
and e-Tree
SONET/SDH functionality
• Cross-connection
• Termination
• Ethernet mapping over SONET/SDH
¬ Generic framing procedure:
GFP, G.7041
• Virtual concatenation (VCAT)
• Link capacity adjustment scheme
(LCAS)
• Performance monitoring
• HO and LO capabilities
DWDM functionality
• Node configurations
¬ Terminal
¬ in-line amplifier (iLA)
• Network configurations
¬ point-to-point
¬ Linear
¬ Ring
¬ Mesh
Protection
• Ethernet network protection
¬ RSTP: 802.1w
¬ MSTP: 802.1s
¬ Link aggregation
• T-MPLS network protection
¬ Tunnel Lin Protection 1:1
• SONET/SDH network protection
¬ Single- and dual-ended APS 1 + 1
¬ Subnetwork Connection
protocol (SnCp), unidirectional
path-switched ring (UPSR)
¬ Multiplex Section-protection
Ring (MSPRING) 2F bidirectional
line switching ring (BLSR)
• Equipment protection
¬ power protection
¬ Controller protection
¬ Universal switch protection
G-MPLS control plane
• T-MPLS tunnel setup
• TDM HO path setup
Management
• Alcatel-Lucent 1350 Optical
Management System (oMS)
• TL1
• Zero-installation craft (ZIC) terminal
• Command line interface (CLI)
• Simple Network Management
protocol (SnMp)
• Secure Shell (SSH) v2/Secure
Sockets Layer (SSL) for secure
connection
Physical specifications
ANSI
Dimensions: Alcatel-Lucent 1850
TSS-160 subrack
• Subrack dimensions
¬ Height: 304 mm (12.0 in.)
¬ Width: 498 mm (19.6 in.)
¬ Depth: 305 mm (12.0 in.)
or 356 mm (14.0 in.)
• Designed to be installed in a
standard AnSi rack
¬ Height: 2.13 m (7.0 ft.)
¬ Width: 660 mm (26.0 in.)
¬ Depth: 305 mm (12.0 in.)
or 356 mm (14.0 in.)
Power and cooling
• Power supply: DC feed (-48-V DC
nominal)
• Power supply: -58-V
• Power consumption: up to 2000 W
• Cooling: forced air
Environment
• Operating temperature:
-5°C to +45°C (23°F to 113°F)
• Relative humidity: 0% to 90%,
non-condensed
Regulatory compliance
• CE and UL certification
• NEBS level 3
• FCC part 15 class A
ETSI
Dimensions: Alcatel-Lucent 1850
TSS-160 subrack
• Subrack dimensions
¬ Height: 304 mm (12.0 in.)
¬ Width:498 mm (19.6 in.)
¬ Depth: 290 mm (11.4 in.)
• Designed to be installed in a
standard eTSi rack
¬ Height: 2.20 m (7.2 ft.)
¬ Width: 600 mm (23.6 in.)
¬ Depth: 300 mm (11.8 in.)
Power and cooling
• Power supply: DC feed (-48-V DC
nominal)
• Power supply: -65-V
• Power consumption: up to 2000 W
• Cooling: forced air
Environment
• Operating temperature:
-5°C to +45°C (23°F to 113°F)
• Relative humidity: 0% to 90%,
non-condensed
Regulatory compliance
• CE certification
• Operating conditions:
eTS 300 019, Class 3.2
• Storage conditions:
eTS 300 019, Class 1.2
• Transportation conditions:
eTS 300 019, Class 2.2
• Electrostatic discharge (ESD)/elec-
tromagnetic compatibility (EMC):
eTS 300 386 “Telecommunications
Center”