LEADER LV 58SER06 User Manual
Page 2
34
Amplitude Accuracy
±0.5 %
Horizontal Axis
Line Display
Display Format
Overlay:
1H, 2H
Parade:
1H, 2H, 3H
Magnification
x1, x10, x20, ACTIVE, or BLANK
Cursor Measurement
Composition
Horizontal Cursors
2 (REF and DELTA)
Vertical Cursors
2 (REF and DELTA)
Amplitude Measurement
Percentage and voltage displays
Time Measurement
Second display
Frequency Measurement
Computes and displays the frequency with the
length of one period set to the time between two
cursors
Vectorscope Display
Scale
75 % or 100 % (color bar)
Gain
x1, x5, IQ-MAG, or variable
Variable Gain
x0.2 to x10
Amplitude Accuracy
±0.5 %
IQ Axis
Show or hide
Pseudo-Composite Display
Converts component signals into composite sig-
nals with artificially added burst and displays the
results (The color matrix is converted to SDTV.)
Picture Display
Display Format
Samples pixels and displays them (R, G, and B
each use 8 bits)
Marker Displays
Center marker, 4:3 marker, safe action marker,and
safe title marker
Gamut Error Display
Marks the areas of the picture that exhibit gamut
errors
Line Select
Marks the selected line
Display Sizes
Compressed and full frame
Status Display
3G-SDI Signal Status Display
Signal Detection
Detects the presence of a 3G-SDI signal
Format
Detects from the supported video signal formats
(When the LV 58SER06 is configured to automati-
cally set the format, the format is detected from
the payload ID.)
Embedded Audio Channel Displays the embedded audio channel number
(Only the audio data of data stream 1 is supported.)
3G-SDI Signal Error Detection
CRC Error
Detects 3G-SDI signal transmission errors
TRS Error
Detects TRS position and protection bit errors
Line Number Error
Detects 3G-SDI signal line number errors
Illegal Code Error
Detects data within the range of 000h to 003h and
3FC to 3FF in locations other than the TRS and
ADF headers
Ancillary Data Error Detection
Checksum Error
Detects ancillary data transmission errors
Parity Error
Detects ancillary data header parity errors
Image Quality Error Detection
Frequency Response
Approx. 1 MHz LPF (IEEE STD 205 response) and
approx. 2.8 MHz LPF (removes transient compos-
ite gamut and gamut errors due to overshoot and
other anomalies)
Gamut Error
Detects time-specified gamut errors
Upper Limit
90.8 to 109.4 %
Lower Limit
–7.2 to 6.1 %
Area Specification
0.1 to 5.0 %
Time Specification
1 to 60 frames
Composite Gamut Error
Detects level errors that occur when component
signals are converted to composite signals
Upper Limit
90.0 to 135.0 %
Lower Limit
–40.0 to 20.0 %
Area Specification
0.1 to 5.0 %
Time Specification
1 to 60 frames
Embedded Audio Error Detection
(Only data stream 1 is supported
for 3G-SDI level B.)
BCH Error
Detects transmission errors in the audio packets
that are embedded in 3G-SDI signals
DBN Error
Detects audio packet continuity errors
Parity Error
Detects parity errors in the audio packets that are
embedded in 3G-SDI signals
Embedded Position Error
Detects the presence of audio in lines where it
should not be embedded
Event Log
Recorded Events
Errors, changes in the input channel, and time
stamps
5 Bar Display
Bar Display
Displays the Y GBR component and composite
gamut
(When you are using line select, only the compo-
nent gamut of the selected line is detected.)
Error Level Setting
Component Gamut
The same as the gamut error
Composite Gamut
The same as the composite gamut error
Frequency Response
The same as the gamut error
Analysis Features
Data Dump Display
Display Format
Displays data separated by serial data sequence
or by channel
(The 3G-SDI level B data dump can display data
stream 1, data stream 2, and data stream 1 and 2
simultaneously.)
Line Select
Displays the selected line
Sample Select
Displays from the selected sample
Jump Feature
Moves to EAV or SAV with the press of a single
button
Data Output
Data can be saved as text files to USB memory or
to a PC over an Ethernet
Audio Control Packet Display
(Only data stream 1 is
supported for 3G-SDI level B.)
Display Details
Displays audio control packet analysis
Display Format
Text, hexadecimal, and binary
Group Selection
Select one group from four available groups
Format ID Display
Corresponding Standard SMPTE 352M
Display Details
Displays payload ID packet analysis
ANC Packet Display
(Only data stream 1 is
supported for 3G-SDI level B.)
ANC Specification Method
DID/SDID
Display Format
Hexadecimal and binary
Time Code Display
(Only data stream 1 is
supported for 3G-SDI level B.)
Supported Time Codes
LTC and VITC (SMPTE 12M-2)
Display Mode
The instrument's internal clock or the time code
Embedded Audio Processing
Clock Generation
Generated from the video clock
Synchronization
All audio channels must be synchronized to the
video clock.
Phases
All phases must be in-sync.
Channel Separation
You may select a maximum of 4 groups of 16
channels each.
(Only data stream 1 is supported for 3G-SDI level B.)
* You need an LV 58SER40A unit to display and
generate audio.
Frame Capture Feature
Function
Captures frame data
Capture Timing
Manual and automatic (error capture)
Display
Displays the captured frame data or superimposes
the captured frame data over the input signal
Media
Internal memory (RAM) and USB memory
You can only record one frame of data to the inter-
nal memory.
Data Output
Screen captures can be saved as .dpx files, .tif
files, or in a file format that the instrument can
load. They can be saved to USB memory or sent
to a PC through an Ethernet connection.
Data Input
Data saved to USB memory can be loaded and
displayed on the instrument.*1
Error Capturing
Automatically captures frame data when an error
occurs
*1 Captured data cannot be displayed unless the
instrument is receiving a 3G-SDI signal that
matches the format of the captured signal.
Environmental Conditions
Conforms to those for the LV 5800 or LV 7800
Power Consumption
Supplied from the instrument; 18 W max.
Weight
0.24 kg
0.53 lbs.
Accessory
Instruction manual .............................................1
LV 5800/LV 7800 Platform Options
Leader Instruments Corporation web :
http://www.LeaderUSA.com
Tel. : 1 (714) 527‐9300
6484 Commerce Drive, Cypress, CA 90630
e‐mail :
Fax : 1 (714) 527‐7490