Controlled Products Systems Group XT-1 - Manual (Page 2)

IN
STR
,I
N
STL
,XT-1
LINE
A
R
P
/N: 215227 C
M
A
TER
IAL
: 2
0
L
B
. M
EAD
BON
D
S
IZE
: 8.500" X
11.000"
SC
AL
E:
1
-1
IN
K:
BL
AC
K
SI
D
E
2
OF 2
(BAC
K)
6. SET TRANSMITTER SWITCHES 7. CONNECT POWER AND TRIGGER INPUTS 8. MOUNT ANTENNA AND ROUTE CABLE
9. TEST SYSTEM 10. COMPLETE INSTALLATION LINEAR LIMITED WARRANTY
This Linear product is warranted against defects in material and workmanship
for twelve (12) months. The Warranty Expiration Date is labeled on the product.
This warranty extends only to wholesale customers who buy direct from Linear or
through Linear’s normal distribution channels. Linear does not warrant this product
to consumers. Consumers should inquire from their selling dealer as to the nature of
the dealer’s warranty, if any. There are no obligations or liabilities on the part of
Linear LLC for consequential damages arising out of or in connection with use
or performance of this product or other indirect damages with respect to loss of
property, revenue, or profit, or cost of removal, installation, or reinstallation. All
implied warranties, including implied warranties for merchantability and implied
warranties for fitness, are valid only until Warranty Expiration Date as labeled on the
product. This Linear LLC Warranty is in lieu of all other warranties express or
implied.
All products returned for warranty service require a Return Product Authorization
Number (RPA#). Contact Linear Technical Services at 1-800-421-1587 for an RPA#
and other important details.
IMPORTANT !!!
Linear radio controls provide a reliable communications link and fill an important need
in portable wireless signaling. However, there are some limitations which must be
observed.
1 WARNING: THIS PRODUCT IS NOT TO BE USED IN LIFE SAFETY APPLICATIONS. FCC Rules allow
unlicensed high-power transmissions at or near the operating frequency of this product which may
interfere with, or even disable, normal operation of this radio device.
1 For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as Part 95
Radio Control devices. As such, they have limited transmitter power and therefore limited range.
1 A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals
that occur on or near their operating frequencies, regardless of code settings.
1 Changes or modifications to the device may void FCC compliance.
1 Infrequently used radio links should be tested regularly to protect against undetected interference or fault.
1 A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or
dealer, and these facts should be communicated to the ultimate users.
Copyright © 2005 Linear LLC 215227 C
ANT-1A
ANTENNA
USE ANT-1A ANTENNA
FOR SHORT RANGE (LESS
THAN 1 MILE)
APPLICATIONS
CON-180A
STRAIGHT
CONNECTOR
CON-180A + CON-90A
ANGLE CONNECTOR
MOUNT ANTENNAS AS HIGH AS POSSIBLE
(A METAL MOUNTING POLE IS RECOMMENDED)
AN 18-FOOT RG-58 CABLE IS SUPPLIED WITH THE
ANT-2 KIT. UP TO 50 FEET OF RG-58 CAN BE USED.
USE RG-8 FOR UP TO 100-FOOT CABLE RUNS.
TO UNIT
USE 3-FOOT LONG ANT-2 ANTENNA FOR LONGER
RANGE APPLICATIONS OR DIFFICULT
INSTALLATIONS
SET SYSTEM CODE SWITCHES A & B
TO MATCH SYSTEM CODE
SWITCHES A & B IN THE RECEIVER
OPTION SWITCH
RECEIVER CHANNEL
SWITCH 1 SWITCH 2 CH #
OFF OFF 1
SET SWITCHES 1 & 2 TO SELECT THE
RECEIVER CHANNEL THE TRANSMITTER
ACTIVATES (USE CHANNEL 1 FOR SINGLE
CHANNEL RECEIVERS)
ON OFF 2
OFF ON 3
ON ON 4
SYSTEM CODE SWITCHES
RECEIVER BANK
SWITCH 3 SWITCH 4 BANK #
OFF OFF 1
SET SWITCHES 3 & 4 TO SELECT THE
RECEIVER BANK THE TRANSMITTER
ACTIVATES (USED ONLY FOR 16 CHANNEL
RECEIVER, USE BANK 1 FOR ALL OTHERS)
ON OFF 2
OFF ON 3
ON ON 4
STATUS REPORTS
OFF
ON
NO STATUS REPORTS
STATUS REPORTS
SWITCH 5
AUTO RESTORAL
OFF
ON
MANUAL RESTORE
AUTO RESTORE
SWITCH 6
SWITCH "A"
SWITCH "B"
OPTION SWITCH
SLIDE BOARD INTO
CASE IN THE 3RD
SLOT UP
TRANSMITTER
RECEIVER
INSTALL AND SETUP
THE COMPANION UNIT
AS DESCRIBED IN ITS
INSTALLATION
INSTRUCTIONS
APPLY POWER AND TRIGGER THE
TRANSMITTER'S INPUT
THE TRANSMIT INDICATOR
SHOULD LIGHT WHEN THE
TRANSMITTER IS TRIGGERED THE RECEIVER'S SIGNAL
INDICATOR SHOULD LIGHT AND
OUTPUT SHOULD ACTIVATE
IF SYSTEM FAILS TEST, CHECK POWER, SWITCH
SETTINGS AND ANTENNA CONNECTIONS
WARNING
NEVER CONNECT THE TRANSMITTER AND
RECEIVER ANTENNA CONNECTORS
DIRECTLY TO EACH OTHER. MAJOR
DAMAGE TO BOTH UNITS WILL OCCUR!
SECURE END PLATE BY
INSTALLING THE FOUR
CASE SCREWS
TIGHTEN WIRING STRAIN
RELIEF BUSHING TO
SECURE AND WEATHER
PROOF WIRING
INSTALL THE TWO REMAINING
MOUNTING SCREWS
TEST SYSTEM AGAIN AFTER
COMPLETING INSTALLATION
1/8 W
Minimum
GND GND + 12 VDC INPUT
FROM 12 VDC, 2-AMP
REGULATED POWER SOURCE
TRIGGERING DEVICE
(N/O OR N/C)
SET INPUT SELECT JUMPER TO MATCH INPUT TYPE
JUMPER SET FOR
NORMALLY OPEN JUMPER SET FOR
NORMALLY CLOSED
USE 18-24 AWG WIRE
TO CONNECT POWER
AND TRIGGER INPUT
ROUTE WIRES THROUGH CASE
STRAIN RELIEF BUSHING BEFORE
CONNECTING TO TERMINALS WARNING
THIS UNIT REQUIRES 12 VDC AT 2 AMPS.
THE NO-LOAD VOLTAGE OF THE SUPPLY
MUST NOT EXCEED 17.5 VDC OR DAMAGE
TO THE UNIT WILL OCCUR!
NOTE: MAXIMUM POWER WIRE
RUN 25-FEET WITH 18 AWG WIRE
FOR RUNS LONGER THAN 3' CONNECT
THE SUPPLIED 10K
Ω RESISTOR FROM
THE +12V SUPPLY TO THE "INPUT"
TERMINALOF THE SENSOR SWITCH.