Controlled Products Systems Group G3T-BX - Manual

Follow these instructions to erase remote codes for
ALL other Genie® openers.
3 LOST OR STOLEN REMOTE
ALL Remote Codes will be erased from Opener
(powerhead) memory.
These instru
NOTE: For openers
manufactured between
1995-1997,
use the two upper
buttons on the remote
ctions are for openers with the type
keypad shown below.
1. Press
PROGRAM
SET
and hold until
both lights come ON
blue. Release button.
2. Lights go out and
Round BLUE light
comes ON.
3. Press
PROGRAM
SET
again and see long
purple LED fl ashing.
4. Press both and
simultaneously on the
powerhead and hold for
5 seconds.
Test remote operation.
Remote should not activate
door opener.
5. Reprogram the Opener with the remaining Remote(s)
(Repeat Section 2 for each remote).
PROGR
AM
SET
—
+
PR
OGRAM
SET
—
+
5 SECS
PROGR
AM
SET
—
+
5 SECS
PROGR
AM
SET
—
+
PROGR
AM
SET
—
PRESS and HOLD until you
SEE BOTH Blue LEDs come ON
SEE long Purple LED
come steady ON
RELEASE
SEE round
Blue LED
come ON
1
2
3
4
5
Programming is complete. This remote button can
now be used to operate door opener.
Repeat as necessary for other remotes or buttons on
the same remote.
PRESS remote and RELEASE
(the button you want to program.)
PRESS and RELEASE
SEE long Purple LED
fl ashing
SEE both LEDs fl ash Blue and go OFF
PRESS and RELEASE remote button again
6 PRESS and RELEASE remote button a third time
1 PROGRAM THE OPENER
3 Button Remote
OPERATING INSTRUCTIONS
PROGRAM
SET
PROGRAM
SET
1. Press and HOLD the Learn Code button on the
powerhead for 10 seconds or until Radio Signal LED
indicator goes out.
2. Reprogram the Opener with the remaining Remotes
following the programming instructions for that
powerhead.
3. Reprogram the Opener with a remote or any other
access device using the instructions accompanying
those devices.
4 BATTERY REPLACEMENT
Replace remote battery with a CR 2032 coin cell battery.
1. Open the remote case using a washer or coin that fi ts
into the slot at the top of the remote.
2. Replace battery. Match battery
polarity with symbols
inside battery housing.
3. Align components and
WARNING
Moving Door can cause serious injury
or death.
• Wall Console must be mounted in sight
of door, at least 5 feet above fl oor and
clear of moving door parts.
• Keep people clear of opening while door is moving.
• Do NOT allow children to play with the Remote or
door opener.
If safety reverse does not work properly:
• Close door then disconnect opener using the
manual release handle.
• Do NOT use Remote or door opener.
• Refer to Door and Door Opener Owner’s Manuals
before attempting any repairs.
2 REMOTE OPERATION
• Point Remote at the garage door and press the
button. Door will move.
• Press the Remote Button again and the door will
stop.
• Press the Remote Button again and the door will
move the opposite way. The door automatically
stops at the end of the open or close cycle.
©2013 GMI Holdings, Inc. DBA The Genie Company Part Number 38381502287 09/2013
snap case closed.
For additional information or help contact Customer Service:
GMI Holdings Inc. d/b/a The Genie Company
1 Door Drive
Mt. Hope, Ohio 44660
FCC and IC CERTIFIED
This device complies with FCC Part 15 and Industry Canada license exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular situation. If this
equipment does cause harmful interference to radio or television reception, which may be determined by turning the
equipment OFF and ON, the user is encouraged to try and correct the interference by one or more of the following
measures: (a) Re-orient or relocate the receiver antenna, (b) Increase the separation between the opener and receiver,
(c) Connect the opener into an outlet on a circuit different from that to which the receiver is connected, and (d) Consult
your local dealer. Any modifications or changes to this equipment which are not expressly approved by the manufacturer
could void the users authority to operate the equipment.
Note: It is possible to press the remote button too quickly or lightly.
If the LED’s do not go off, press the remote button several more
times to achieve confirmation (the LED’s turn off). If the LED’s
turn red, return to Step 1 and repeat steps 1 through 6.
5 SECS
Call 1-800-35-GENIE or write: