Programming the remote control to the receiver – Controlled Products Systems Group 355LM User Manual

Page 2

114A3099E

PROGRAMMING THE REMOTE CONTROL TO THE RECEIVER

With Security✚

, the code between the remote control and the receiver

changes with each use, accessing over 100 billion new codes.

You can activate your garage door opener with up to 8 Security✚

remote controls and one Security✚

Keyless Entry.

1. Pry open the front panel of receiver case with a coin or a screwdriver

(Figure 4). Re-connect power to the garage door opener.

2. Press and release the “SMART” button on the receiver. The “SMART”

indicator light will glow steadily for 30 seconds (Figure 5).

3. Within 30 seconds, press and hold the button on the hand-held

remote control that you wish to operate your garage door opener
(Figure 6).

The garage door opener will now operate when the push button on either
the receiver or the remote control is pressed.

Repeat steps 2 and 3 for each remote control that will be used to operate
the garage door opener.

TO ERASE ALL REMOTE CONTROL CODES

Press and hold the “SMART” button on the receiver panel until the
indicator light turns off (about 6 seconds). All remote control codes are
now erased. Then follow the steps above to reprogram each remote
control.

REPLACING THE REMOTE CONTROL BATTERY

The lithium battery should produce power for up to
5 years. To replace battery, pry open case with visor
clip or screwdriver, as shown. Insert battery positive
side up. Dispose of old battery properly.

SET OUTPUT DURATION (COMMERCIAL APPLICATIONS ONLY)

For commercial applications, the receiver can be set for either constant or
momentary closure on the output contacts. Use of constant closure is
prohibited on residential garage door openers because it overrides the
safety reversal devices.

With the jumper in the “M” (Momentary) position, the contacts will close
for 1/4 second regardless of the length of radio transmission. With the
jumper in “C” (Constant) position, the contacts will stay closed as long as
the radio continues transmitting.

The receiver is factory set at M.

To prevent possible SERIOUS INJURY or DEATH, the use of
CONSTANT OPERATION on residential openers is PROHIBITED.

ATTENTION

AVERTISSEMENT

WARNING

CAUTION

WARNING

PRECAUCIÓN

ADVERTENCIA

To prevent possible SERIOUS INJURY or DEATH:
• NEVER allow small children near batteries.
• If battery is swallowed, immediately notify doctor.

ATTENTION

AVERTISSEMENT

WARNING

CAUTION

WARNING

PRECAUCIÓN

ADVERTENCIA

Indicator
Light

“SMART”

Button

Option

Jumper

FOR SERVICE DIAL OUR TOLL FREE NUMBER: 1-800-528-9131

Output
Duration
Terminals

Jumper

MOMENTARY
OPERATION

Output
Duration
Terminals

Jumper

CONSTANT
OPERATION

SPECIFICATIONS

Output Rating . . . . . . . . . . . . . . . . . . . . . . . . . 5 Amps 28VAC or DC Max.
Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18V - 30V ~, 30mA, 60Hz

18 - 30V , 30mA

RF Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 315MHz
If the power is other than shown in specifications, Accessory Transformer
Model 85 or 95 is required.
Accessory Remote Controls — Series 300.

NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of
this receiver and/or remote control are prohibited, except for changing the code setting or
replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.

Figure 5

Figure 6

Figure 4