Accusplit AL1590M12 - Manual (Page 2)

EXCLUSIVE DISTANCE ACCURACY TIP
Maximize the accuracy of your distance measurement by:
• Walking a measured 0.5 or 1.0 mile/km. (We recommend
that you use a 1 ⁄
4
-mile/400 meter track like those found at
a high school).
• Compare the DISTANCE recorded to the measured
distance. If the pedometer shows you walked LESS than
you actually did, reset your STEP LENGTH to a longer
setting. If the pedometer shows you walked MORE than
you actually did, reset the STEP LENGTH to a shorter
setting.
To view the current week total data, press the gray WK-DAY
button from any display mode. The total count so far for the
current week is displayed. The word “WEEK” will appear in the
upper right band corner of the display. Press the gray WK-DAY
button again to return to today’s data. Or, press the black MODE
button to cycle through the current week’s results.
AUTO MOVEMENT SENSOR
1. To filter out random movements, the unit remains in standby
mode until 5 continuous steps are registered. Only then are
the 5 steps calculated in, and an Active indicator “▲” appears
on the upper left of display.
2. When regular walk/run movement stops, after 2 seconds the
timer pauses and the unit switches to standby status (Active
indicator “▲” disappears).
RESETTING YOUR PEDOMETER
Auto Zero Reset:
The daily count of steps, distance, calories,
and activity time resets each night automatically at 2:00 AM.
However, the records will remain on the display until you have
taken your first five steps (so that you can manually record them
if desired). At 2:00 AM on Sunday, the previous week’s records
will also be reset to zero, but they remain on the display until
you’ve taken your first five steps of the week. At this point, the
current week’s memories will be transferred to the previous
week’s memories.
Manual Zero Reset:
You can also manually reset your pedometer
at any time. To reset today’s memories, first press the gray WK-
DAY button until the unit is in DAY mode. In DAY mode, you will
see only one day of the week at the top of the display. Next,
press and hold the yellow RESET button for at least 2 seconds.
To reset the current week’s memories, first press the gray WK-
DAY button until the word “WEEK” appears in the upper right
hand corner of the display. Next, press and hold the yellow
RESET button for at least 2 seconds.
REPLACING THE BATTERY
When the display starts to dim or goes blank, it is time to replace
the battery. Your pedometer uses one Type LR44 1.5 volt alkaline
battery. To replace:
1. Insert a coin into the slot on the bottom of the case, and twist
counterclockwise to loosen the case front. Lift case front away.
2. Using a pen or other thin object, push battery sideways out of
its holder. Replace it with a new battery. The battery’s positive
(+) terminal should be FACE UP while you put it into the
pedometer.
3. Align case front over the pedometer and press gently to snap
cover back into place, starting with top.
• RESET display to zero.
• Walk the track again to test the adjustment, and re-adjust
accordingly.
• Once adjusted DO NOT ALLOW ANYONE ELSE TO CHANGE
THE SETTING because the Activity Pedometer is now set for
your style.
• You are now ready to walk any route, change that route freely
and still get an accurate measurement of distance for your
fitness or recreation program.
First, loop the
pedometer clip
Next, loop the metal
clip, then clasp clothing
Or, loop a
badge holder, then
put into pocket
(Badge holder
not included)
Or, loop a belt or belt loop
Attaching the Leash: Attach the pedometer to the leash by
looping the leash around the pedometer belt clip. Next, clasp
the waistband of your clothing with the attached clip. You can
also use a safety pin to fasten the leash to your clothing, or
loop the leash through your belt or belt loop.
VIEWING YOUR RESULTS
Once you put on your pedometer with the cover closed, it will
automatically begin to record your steps, distance, calories
burned, and activity time. Repeatedly press the black MODE
button to cycle through the pedometer modes:
STEPS → DISTANCE → CALORIES → ACTIVITY TIMER →
TIME OF DAY → STEPS
MEMORIES
This pedometer has memories to keep track of today’s, this
week’s, and last week’s step activity, distance, calories, and
activity time.
To view the previous week’s total data, press the gray PREV
WK button from any display mode. The previous week’s total
for that mode is displayed. Press the black MODE button
to cycle through the display modes. All seven day of week
indicator bars (at top of display) are visible when viewing
PREVIOUS WEEK data. Press the gray PREV WK button to
return to today’s data.