All-Flo A050 Series 1/2 Aluminum - Manual (Page 4)

all-flo.com
MODEL DESIGNATION MATRIX -
ALUMINUM
SECTION
2
4
PR
ODUC
T SERIE
S
FL
UID CONNE
CTION T
YPE
FL
UID CHAMBER
S/
MANIFOLDS
DIAPHRA
GM
VAL
VE/B
ALL
VAL
VE SEA
T
O-RINGS
SPE
CIAL (
OTHER)
POR
TING
INTERMEDIA
TE/
INNER CHAMBER
SPE
CIAL
(HARD
WARE,
MUFFLER, L
UG)
A 0 5 0 - 1 2 3 - 4 5 6 7 - 8 9 10
FLUID CONNECTION TYPE
N = NPT
B = BSP
INTERMEDIATE / INNER CHAMBER
A = Aluminum
P = Polypropylene (Glass Filled)
FLUID CHAMBER / MANIFOLDS
A = Aluminum
DIAPHRAGMS
G = Geolast ®
S = Santoprene ®
T = PTFE with Santoprene® Backup
N = Buna – N
E = EPDM
V = Viton
®
VALVE/BALL
G = Geolast ®
S = Santoprene ®
T = PTFE
E = EPDM
V = Viton
®
3 = 316 Stainless Steel
VALVE SEAT
P = Polypropylene
3 = 316 Stainless Steel
A = Aluminum
K = PVDF
Y = Nylon
O-RINGS
N = Buna-N
E = EPFM
T = PTFE
V = Viton
®
PORTING
0 = Standard (Suction Right / Discharge Right)
T = Suction Right / Discharge Left
X = Suction Left / Discharge Right
Y = Suction Left / Discharge Left
A = Suction Center Front / Discharge Center Front
B = Suction Center Front / Discharge Center Rear
C = Suction Center Front / Discharge Top
D = Suction Center Front / Discharge Right
E = Suction Center Front / Discharge Left
F = Suction Center Rear / Discharge Center Front
G = Suction Center Rear / Discharge Center Rear
H = Suction Center Rear / Discharge Top
I = Suction Center Rear / Discharge Right
J = Suction Center Rear / Discharge Left
K = Suction Bottom / Discharge Center Front
L = Suction Bottom / Discharge Center Rear
M = Suction Bottom / Discharge Top
N = Suction Bottom / Discharge Right
O = Suction Bottom / Discharge Left
P = Suction Right / Discharge Center Front
Q = Suction Right / Discharge Center Rear
R = Suction Right / Discharge Top
U = Suction Left / Discharge Center Front
V = Suction Left / Discharge Center Rear
W = Suction Left / Discharge Top
1 = Dual Suction
2 = Dual Suction / Dual Discharge
3 = Dual Discharge
4 = All Ports Open (Standard ports will be left
un-plugged)
SPECIAL OPTION (HARDWARE, MUFFLER, LUG)
0 = Standard (Zinc Plated Steel Hardware, Plastic
Muffler)
4 = Zinc Plated Steel Hardware, Metal Muffler
7= Stainless Steel Hardware, Plastic Muffler
8 = Stainless Steel Hardware, Metal Muffler
B = PTFE Coated Stainless Steel Hardware,
Plastic Muffler
C = PTFE Coated Stainless Steel Hardware,
Metal Muffler
D = Zinc Plated Steel Hardware, Plastic Muffler,
Grounding Lug Installed
E = Zinc Plated Steel Hardware, Metal Muffler,
Grounding Lug Installed
F = Stainless Steel Hardware, Plastic Muffler,
Grounding Lug Installed
G = Stainless Steel Hardware, Metal Muffler,
Grounding Lug Installed
H = PTFE Coated Stainless Steel Hardware,
Plastic Muffler, Grounding Lug Installed
I = PTFE Coated Stainless Steel Hardware,
Metal Muffler, Grounding Lug Installed
SPECIAL OPTION (OTHER)
0 = Standard (None)
1 = Cycle Counter Valve
2 = Solenid Adaptor Valve 110/50 Volt AC,
120/60 Volt AC
3 = Solenid Adaptor Valve 110/50 Volt AC,
120/60 Volt AC Explosion Proof
4 = Solenid Adaptor Valve 220/50 Volt AC,
240/60 Volt AC, 12 Volt DC
5 = Solenid Adaptor Valve 220/50 Volt AC,
240/60 Volt AC, 12 Volt DC Explosion Proof
6 = Solenid Adaptor Valve 220/50 Volt AC,
240/60 Volt AC, 125 Volt DC
7 = Solenid Adaptor Valve 220/50 Volt AC,
240/60 Volt AC, 125 Volt DC Explosion Proof
8 = Solenid Adaptor Valve 24 Volt DC
9 = Solenid Adaptor Valve 24 Volt DC,
Explosion Proof
A = Grease Free (No Lubrication Assembly)
SIZE
WET END REPAIR KIT
Wet end kits are available and
consist of diaphragms, (back-up
diaphragms if required), balls,
seats and seat o-rings.
See matrix below.
1
2
6
7
8
9
10
INTERMEDIATE / INNER CHAMBER
A = Aluminum
P = Polypropylene (Glass Filled)
Bold indicates recommended options
AIR END REPAIR KIT
Air end repair kit contains pilot sleeve as-
sembly, diaphragm rod and main air valve.
DIAPHRA
GM
VAL
VE/B
ALL
VAL
VE SEA
T
O-RINGS
A W E - 0 5 0 - 4 5 6 7
PR
ODUC
T
SERIE
S
WET END REP
AIR KIT
PUMP SIZE
MA
TERIAL
A A K - 0 5 0 - 2
PR
ODUC
T
SERIE
S
PUMP SIZE
AIR END
REP
AIR KIT
3
4
5
* Solenid Adaptor Valves only available on select pump models with polypropylene intermediate