Extron Electronics MTP 1500RL 15HD RS SEQ Setup Guide User Manual
Page 2
MTP 1500RL 15HD RS SEQ • Setup Guide (Continued)
Extron USA Headquarters +1.800.633.9876 (USA/Canada Only)
Extron USA - West: +1.714.491.1500 FAX: +1.714.491.1517
Extron USA - East: +1.919.850.1000 FAX: +1.919.850.1001
© 2013 Extron Electronics — All rights reserved. All trademarks mentioned are the property of their respective owners.
www.extron.com
Step 5 — Power
Power Supply
Output Cord
SECTION A–A
Ridges
Smooth
A
A
Tie
Wrap
POWER
12V
xA MAX
Rear
Panel
Ridges
Earth
Ground
3/16"
(5 mm)
Max.
Wire the 2-pole captive screw connectors for the included external 12 VDC power supplies (see
image
a
on the right). Plug them into all units.
Grounding guidelines
Extron MTP 1500RL 15HD RS SEQ products can be adversely affected by electrostatic discharge (ESD)
if they are not grounded correctly.
To prevent malfunctions or product damage, an experienced installer can correctly ground an Extron
MTP 1500RL 15HD RS SEQ product in either of two ways:
•
Ground the power input port — Insert one end of the grounding wire to the negative or ground pin
on the power input connector (see image
a
on the right). Tie the other end of the wire to an earth
ground.
•
Ground the chassis — Use a connector hex nut (see image
b
on the right). Tie the other end of
the wire to an earth ground.
If you have any questions about how to ground a product in a specific application, contact an Extron technical
support specialist.
Step 6 — Peaking and Level
Adjust the image sharpness using the
Peaking control. Increased peaking compensates for mid- and high-frequency
RGB
PEAKING
LEVEL
MIN/MAX
detail loss. The LED lights red when minimum (zero) or maximum peaking is reached.
Adjust the image brightness using the
Level control. View the image and adjust either control for the best image quality.
Step 7 — Skew Compensation
Pair skew can be measured with test equipment or by viewing a crosshatch test pattern. The SEQ receivers have
built-in skew compensation capabilities. Adjust the equalization as follows:
A.
Set the skew delay to zero for red, green, and blue by using a Tweeker or small screwdriver to press and hold
DELAY
RED
GREEN
BLUE
SELECT
ADJUST
the Select button for 3 seconds. When the Red, Green, and Blue LEDs all go out, release the Select button.
B.
Use UTP cable test equipment or examine the displayed image to determine which video signal — red, green,
or blue —
is shifted furthest to the right.
C.
Adjust the furthest left video signal by using a Tweeker or screwdriver to press and release the Select button until
the LED for the left-shifted color lights.
D.
Slowly rotate the Adjust control clockwise until the shifted color is properly aligned.
E.
Repeat steps C and D to align the third color if needed.
68-1555-50
Rev. C
01 13
Figure 1.
Example of a Typical MTP 1500RL 15HD RS SEQ Application
INP
UT
Tx
Rx
RS-232
MON
ITOR
PO
WE
R
12V
.5A MA
X
OUTPUT
CABL
E
NORM
LO
NG
MT
P T
VG
A
RS
PO
WER
12V
1.0A
MA
X
RS-
232
Rx
Tx
OUTP
UT
INPU
T
BUFFER
ED OU
TPU
T
MTP 1500RL
15HD
RS SE
Q
H
+
V
+
CSYN
C
SO
G
VIDE
O
EN
D
BI-232
ON
MT
P
MT
P
POWE
R
12V
1.0A
MA
X
RS-232
Rx
Tx
OUTPUT
INP
UT
BUFFERED O
UTPU
T
MTP 1500RL 15HD RS SE
Q
H
+
V
+
CSYN
C
SO
G
VIDE
O
EN
D
BI-232
ON
MT
P
MT
P
PC
Flat Panel
Display
Flat Panel
Display
Extron
MTP 1500RL 15HD RS SEQ
Twisted Pair Receiver
with Loop-Through and Skew EQ
500' (152 m) UTP Cable
(CAT 5/5e/6)
Extron
MTP T 15HD RS
Twisted Pair
Transmitter
RS-232
RS-232
RGBHV
RGBHV
500' (152 m) UTP Cable
(CAT 5/5e/6)
RS-232
RGBHV
Extron
MTP 1500RL 15HD RS SEQ
Twisted Pair Receiver
with Loop-Through and Skew EQ
Maximum transmission distances:
Data (RS-232) 1000' (305 m)
Video 15 00' (457 m)
b
a