Extron Electronics MTP 1500RL 15HD RS SEQ Setup Guide - Manual

IMPO
RTAN
T:
Go to www
.extron.com f
or the complete
user guide
, installation instructions,
and
specifications bef
ore connecting the
product to the po
wer sour
ce.
MTP 1500RL 15HD RS SEQ • Setup Guide
This guide provides basic instructions for an experienced installer to set up and operate the Extron MTP 1500RL
15HD RS SEQ twisted pair receiver.
For full details, see the MTP 1500RL 15HD RS SEQ User Guide, available online at www.extron.com.
INPUT BUFFERED OUTPUT
POWER
12V
1.0A MAX
MTP 1500RL 15HD RS SEQ MTP
RS-232
Rx Tx
OUTPUT
MTP
ON
H
+
V
+
CSYNC SOG VIDEO END BI-232
MTP 1500RL SERIES RGB
PEAKING LEVEL
DELAY
RED
GREEN
BLUE
SELECT
ADJUST MIN/MAX
MTP MTP
Installation and Setup
Step 1 — Mounting
Turn off or disconnect all equipment power sources. Mount the MTP 1500RL 15HD RS SEQ receiver as required.
Step 2 — Connect Input
Connect the RJ-45 cable from an MTP transmitter to the Input port on the MTP 1500RL 15HD RS SEQ receiver.
Terminate the cable as shown below right, using the same standard (T568A or T568B) at both ends.
Input
Source
MTP Tx
Device Display
MTP RL Rx
Device
Input
Source
MTP Tx
Device
MTP 1500RL
15HD RS Device
Display
Transmission distance with one device before the MTP 1500RL 15HD RS SEQ
Transmission distance with more than one device before the MTP 1500RL 15HD RS SEQ
VGA
cable
VGA
cable
TP
cable
1000 feet (305 m) maximum
(RS-232 data signals)
MTP 1500RL
15HD RS Device
VGA
cable
VGA
cable
TP
cable
TP
cable
1500 feet (457 m) maximum (video signals)
1500 feet (457 m) maximum (video signals)
1000 feet (305 m) maximum
(RS-232 data signals)
NOTE: The transmitter and receiver are designed for and perform best with Extron Enhanced Skew-Free ™ AV cable terminated in accordance
with the TIA/EIA T568A standard. CAT 5 cables are acceptable but less preferable. Using preterminated and tested cables is also
recommended. Cables terminated on site should be tested before use to ensure that they comply with Category 5 specifications.
Step 3 — Connect Outputs
Attach the applicable output cables (video, audio, and buffered output).
Ground
Tx
Rx
Gnd
Receive
Transmit
Connected RS-232
Device Pins
MTP Reciever
Pins
A. High resolution video output — Connect a suitable display device to the 15-pin HD
connector (RGB).
B. RS-232 connector — Connect an RS-232 compatible MTP transmitter to the 3-pole
captive screw connector (wired as shown at right) for bi-directional or uni-directional
communication up to 1,000 feet, (305 meters) maximum.
C. Buffered output — Connect up to 5 daisy-chained MTP receivers to this RJ-45 connector.
Step 4 — Receiver DIP Switches
• H sync (H+) and V sync (V+) switches — Set these switches up (On) for positive sync or
down (Off) for negative sync.
• Composite Sync, SOG, and Video switches — Set these switches as shown in the table
(see right) to output the indicated format.
• End Unit switch — Set this switch up if either of the following is true:
• The receiver being configured is the only receiver connected to the transmitter.
• The receiver being configured is the last receiver in a daisy-chained system.
• BI-232 switch — Set this up (ON) for bi-directional or down for uni-directional communication.
Pin T568A Wire
Color T568B Wire
Color
1 White-green White-orange
2 Green Orange
3 White-orange White-green
4 Blue Blue
5 White-blue White-blue
6 Orange Green
7 White-brown White-brown
8 Brown Brown
Insert Twisted
Pair Wires
Pins:
RJ-45 Connector
12345678
Output
Format C Sync SOG Video
RGBHV
RGBS
RGsB
Component*
S-video*
Composite*
* Input video format must match.
ON
H
+
V
+
CSYNC SOG VIDEO END BI-23
2