Extron Electronics MDA 5SV User’s Manual Rev. B - Manual (Page 2)

○
○
○
○
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
○○○○○○○○○○○○○○○○○○○○○○○○○○○○
User’s Guide
MDA 5V, 5SV, 5A RCA • Installation MDA 5V, 5SV, 5A RCA • Installation
Introduction
3 2
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
© 2002 Extron Electronics. All rights reserved.
Extron Electronics, USA
1230 South Le wis Str eet
Anaheim, CA 92805
USA
714.491.1500
Fax 714.491.1517
Extron Electronics, Europe
Beeldschermw eg 6C
3821 AH Amersfoort
The Netherlands
+31.33.453.4040
Fax +31.33.453.4050
Extron Electronics, Asia
135 Joo S eng Road, #04-01
PM Industrial B uilding
Singapor e 368363
+65.6383.4400
Fax +65.6383.4664
Extron Electronics, Japan
Daisan DMJ B uilding 6F
3-9-1 Kudan M inami
Chiyoda-ku, T oky o 102-0074 Japan
+81.3.3511.7655
Fax +81.3.3511.7656 www.extron.com
Mini Distribution Amplifiers
68-614-01 Rev . B
Printed in the USA
08 02
VersaT ools™ MDA 5V, 5SV ,
5A RCA
The Extron MDA 5 Series of Mini Distribution Amplifiers (MDAs)
are a family of three video and audio distribution amplifiers. The
MDA are members of the Extron VersaTools™ line of basic
distribution amplifiers, switchers, and associated video
accessories.
The MDA 5V distributes buffered composite video, the MDA 5SV
distributes buffered S-video (luminance (Y) and chrominance
(C)), and the MDA 5A RCA distributes amplified stereo audio, on
RCA outputs.
The MDAs ship with external, desktop 12V power supplies,
which accept 100-240VAC input.
Installation
The MDA 5V, 5SV, and 5A RCA can be mounted on a rack shelf,
under a desk or tabletop, or on a projector bracket.
Rack mounting
For optional rack mounting, mount the MDA on a VersaTools 19"
1U Rack Shelf (Extron part #60-190-20) (figure 1) or a standard
Universal 1U Rack Shelf (Extron part #60-190-01) (figure 2). On
the standard rack shelf, the MDA mounts in one of four locations
to the rear of the rack or in one of four locations to the front of the
rack.
Figure 1 — Rack mounting the MDA 5V, 5SV, or 5A
RCA on the VersaTools shelf
1 . If feet were previously installed on the bottom of the MDA,
remove them.
2 . Mount the MDA on the rack shelf, using two 4-40 x 3/16
screws in opposite (diagonal) corners to secure the MDA to
the shelf.
3 . Install blank panel(s) or other unit(s) to the rack shelf.
4. Insert the shelf into the rack, aligning the holes in the shelf
with those of the rack.
5. Secure the shelf to the rack using the supplied machine
screws. This shelf can be mounted in the front or in the rear
of the rack.
Only products in the VersaTools line can be mounted to a
VersaTools shelf. Any 1U rack-mountable Extron product
can be mounted on the standard shelf.
Figure 2 — Mounting the MDA on the standard shelf
Furniture or projector mounting
Furniture mount or projector mount the MDA using the optional
mounting kit (Part #70-212-01, furniture, or 70-217-01, projector)
as follows:
1 . Attach the mounting brackets to the MDA with the machine
screws provided (figure 3).
Figure 3 — Desk and projector mounting the
MDA 5V, 5SV, or 5A RCA
FCC Class A Notice
Note: This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference, in which case the user will be required to correct the interference at his
own expense.
Note: This unit was tested with shielded cables on the peripheral devices. Shielded
cables must be used with the unit to ensure compliance.
General
Power................................................ 100VAC to 240VAC, 50/60 Hz, 5 watts,
external, auto-switchable; to 12VDC,
1 A (max.) power supply. Product requires
0.4 A (max).
Temperature/humidity................. Storage -40° to +158°F (-40° to +70°C) / 10%
to 90%, non-condensing
Operating +32° to +122°F (0° to +50°C) / 10%
to 90%, non-condensing
Rack mount...................................... Yes, with optional 1U rack shelf, part #60-
190-01,
or the VersaTools rack shelf, part #60-190-20
Enclosure type.. ............................... Metal
Enclosure dimensions.................... 1.7" H x 4.3" W x 3.0" D (1U high, quarter
rack width)
4.2 cm H x 11.0 cm W x 7.6 cm D
(Depth excludes connectors and knobs.)
Product weight................................ 0.7 lbs (0.3 kg)
Shipping weight.............................. 3 lbs (1.4 kg)
Vibration........................................... ISTA/NSTA 1A in carton (International Safe
Transit Association)
Listings.............................................. UL, CUL
Compliances.................................... CE, FCC Class A, VCCI, AS/NZS, ICES
MTBF................................................. 30,000 hours
Warranty........................................... 3 years parts and labor
Specifications are subject to change without notice.
DIS TRIB UT ION AM PLI FIE R
DISTR IB UT ION A MP LIF IER
DIS TR IB UT IO N A MPL IFIER
MDA S ER IES DIST RIBU TIO N AM PLIF IER
DIS TRIB UTION A MP LIFIER
Ceiling
Digital Projector
Projector
Mounting
Bracket
MD A 5V PO W
E R 15V .5A MAX
1 2
3 4
IN P U T
O U TP
U T S
Mounting
Bolt
Projector Mounting Under Desk Mounting
(2) 4-40 x 3/16" screws
Use 2 mounting holes on
opposite corners
VersaTools Rack Shelf
1/4 Rack Width False Front
Face Plate
DIS TR IBU TION A MP LIF IER
DIS TR IBU TIO N A MP LIF IE R
DIS TR IB UT IO N A MP LIF IER