Extron Electronics MLA-Remote - Manual

MLA-Remote Remote Control Instruction Guide
Install two AAA batteries as shown at right.
Operation
The buttons on the Extron MLA-Remote duplicate the MediaLink™
Controller‘s (MLC’s) front panel controls and also those of an IRCM-VCR and an IRCM-DVD for
normal operation. The MLA-Remote can also be used to control a MediaLink Switcher (MLS).
The controller, control module, or switcher responds to commands from the MLA-Remote as if
the corresponding button or knob were pressed or turned on the controller or switcher.
From a distance of no more than 30 feet and within 40° of the axis (see the illustration on the
other side of this card), the MLA-Remote sends infrared (IR) signals to
• a MediaLink Controller via the controller’s front panel IR pickup device or the IR pickup
device of an optional IR Link IR signal repeater.
• a MediaLink Switcher via a connected IR Link. The switcher can receive signals from the
MLA-Remote only via an IR Link.
Setup operations cannot be performed from the MLA-Remote.
The Display Power button and the VCR and DVD control buttons will not function until
commands have been stored in the MLC 206’s memory. The MLA-Remote’s VCR buttons
control the first (lowest address numbered) IRCM-VCR connected to the MLC. The DVD
buttons control the first (lowest address numbered) IRCM-DVD connected to the MLC.
Commands are transmitted from the MLC 206’s Display/Source Control RS-232 port (via hard
wiring) and IR ports (via IR Emitter or optional IR Broadcaster) when the corresponding button is
pressed on the MLA-Remote or on the controller’s or control module’s front panel. Refer to the
MediaLink Controllers User’s Manual and the Control Modules User’s Manual.
MLA-Remote Remote Control Instruction Guide
Install two AAA batteries as shown at right.
Operation
The buttons on the Extron MLA-Remote duplicate the MediaLink™
Controller‘s (MLC’s) front panel controls and also those of an IRCM-VCR and an IRCM-DVD for
normal operation. The MLA-Remote can also be used to control a MediaLink Switcher (MLS).
The controller, control module, or switcher responds to commands from the MLA-Remote as if
the corresponding button or knob were pressed or turned on the controller or switcher.
From a distance of no more than 30 feet and within 40° of the axis (see the illustration on the
other side of this card), the MLA-Remote sends infrared (IR) signals to
• a MediaLink Controller via the controller’s front panel IR pickup device or the IR pickup
device of an optional IR Link IR signal repeater.
• a MediaLink Switcher via a connected IR Link. The switcher can receive signals from the
MLA-Remote only via an IR Link.
Setup operations cannot be performed from the MLA-Remote.
The Display Power button and the VCR and DVD control buttons will not function until
commands have been stored in the MLC 206’s memory. The MLA-Remote’s VCR buttons
control the first (lowest address numbered) IRCM-VCR connected to the MLC. The DVD
buttons control the first (lowest address numbered) IRCM-DVD connected to the MLC.
Commands are transmitted from the MLC 206’s Display/Source Control RS-232 port (via hard
wiring) and IR ports (via IR Emitter or optional IR Broadcaster) when the corresponding button is
pressed on the MLA-Remote or on the controller’s or control module’s front panel. Refer to the
MediaLink Controllers User’s Manual and the Control Modules User’s Manual.
MLA-Remote Remote Control Instruction Guide
Install two AAA batteries as shown at right.
Operation
The buttons on the Extron MLA-Remote duplicate the MediaLink™
Controller‘s (MLC’s) front panel controls and also those of an IRCM-VCR and an IRCM-DVD for
normal operation. The MLA-Remote can also be used to control a MediaLink Switcher (MLS).
The controller, control module, or switcher responds to commands from the MLA-Remote as if
the corresponding button or knob were pressed or turned on the controller or switcher.
From a distance of no more than 30 feet and within 40° of the axis (see the illustration on the
other side of this card), the MLA-Remote sends infrared (IR) signals to
• a MediaLink Controller via the controller’s front panel IR pickup device or the IR pickup
device of an optional IR Link IR signal repeater.
• a MediaLink Switcher via a connected IR Link. The switcher can receive signals from the
MLA-Remote only via an IR Link.
Setup operations cannot be performed from the MLA-Remote.
The Display Power button and the VCR and DVD control buttons will not function until
commands have been stored in the MLC 206’s memory. The MLA-Remote’s VCR buttons
control the first (lowest address numbered) IRCM-VCR connected to the MLC. The DVD
buttons control the first (lowest address numbered) IRCM-DVD connected to the MLC.
Commands are transmitted from the MLC 206’s Display/Source Control RS-232 port (via hard
wiring) and IR ports (via IR Emitter or optional IR Broadcaster) when the corresponding button is
pressed on the MLA-Remote or on the controller’s or control module’s front panel. Refer to the
MediaLink Controllers User’s Manual and the Control Modules User’s Manual.
MLA-Remote Remote Control Instruction Guide
Install two AAA batteries as shown at right.
Operation
The buttons on the Extron MLA-Remote duplicate the MediaLink™
Controller‘s (MLC’s) front panel controls and also those of an IRCM-VCR and an IRCM-DVD for
normal operation. The MLA-Remote can also be used to control a MediaLink Switcher (MLS).
The controller, control module, or switcher responds to commands from the MLA-Remote as if
the corresponding button or knob were pressed or turned on the controller or switcher.
From a distance of no more than 30 feet and within 40° of the axis (see the illustration on the
other side of this card), the MLA-Remote sends infrared (IR) signals to
• a MediaLink Controller via the controller’s front panel IR pickup device or the IR pickup
device of an optional IR Link IR signal repeater.
• a MediaLink Switcher via a connected IR Link. The switcher can receive signals from the
MLA-Remote only via an IR Link.
Setup operations cannot be performed from the MLA-Remote.
The Display Power button and the VCR and DVD control buttons will not function until
commands have been stored in the MLC 206’s memory. The MLA-Remote’s VCR buttons
control the first (lowest address numbered) IRCM-VCR connected to the MLC. The DVD
buttons control the first (lowest address numbered) IRCM-DVD connected to the MLC.
Commands are transmitted from the MLC 206’s Display/Source Control RS-232 port (via hard
wiring) and IR ports (via IR Emitter or optional IR Broadcaster) when the corresponding button is
pressed on the MLA-Remote or on the controller’s or control module’s front panel. Refer to the
MediaLink Controllers User’s Manual and the Control Modules User’s Manual.