Selected sis commands, Gss 100 • setup guide – Extron Electronics GSS 100 Setup Guide User Manual
Page 4
68-974-50
Rev A
04 11
4
Selected SIS Commands
The table below shows a partial list of SIS commands the you can use for operation and configuration of the GSS. For a complete
listing, see the GSS 100 User Guide. Run the following commands from a PC connected to the RS-232 port (item
e
on page 1).
Command
ASCII Command
(Host to Unit)
Response
(Unit to Host)
Additional description
Recall an image to buffer
EX!
RF
}
Cim
•
X!]
Select image
X!
(file name with extension [*.bmp or *.jpg]) to display.
NOTE
:
It will take several seconds between the issuance of the recall command (
EX!
RF
}
) and the receipt of the Cim response.
Take
%
Tke
]
Swap the displayed and buffered images using the selected effect
(cut or dissolve).
Switch effect
9*
X@
#
Eff
X@]
X@
: 0 = cut
1= dissolve.
Dissolve duration
10*
X#
#
Dur
X#]
Set the duration of the dissolve effect to
X#
, in 0.1-second increments.
Display source
X$
!
Chn
X$]
X$
: 0 = last store image
1= pass-thru
Slide show interval
2*
X%
#
Sli
X%]
Set the display time for each image to
X%
seconds.
Pass-through configuration
1*
X^
#
Pas
X^]
X^
: 0 = pass-thru
1= no pass-thru
Auto-switch and slide show mode
4*
X&
#
Aut
X&]
Set auto-switch and slide show mode.
X&
definitions:
X&
: 0 = off
2 = on/still
1 = off/show
3 = on/show
Stored image output rate
X*
*
X^
=
Rte
X*
*
X(]
Set the output resolution for the stored image to
X*
at
X(
Hz.
See below for
X*
and
X(
definitions.
Stored image output sync format
6*
X1)
#
Syn
X1)]
Set the output sync format of the stored image to
X1)
.
X1)
: 0 = RGBHV
1 = RGBS
Stored image output sync polarity
7*
X1!
#
Pol
X1!]
Set the output sync polarity of the stored image to
X1!
.
X1!
: 0 = H– / V–
2 = H+ / V–
1 = H– / V+
3 = H+ / V+
RGB delay
8*
X1@
#
Dly
X1@]
Mute the RGB output for
X1@
(in 0.1-second increments) before
displaying the RGB pass-through input.
Video mute and unmute
X1#
B
Vmt
X1#]
X1#
: 0 = unmute
1= mute
Front panel locks and unlock
(executive mode)
X1$
X
Exe
X1$]
X1$
: 0 = unlock
2 = complete lock
1 = partial lock
X*
= Resolution
0 = 640 x 480
5 = 1024 x 1024
10 = 1365 x 768
15 = 720p
1 = 600 x 600
6 = 1280 x 768
11 = 1365 x 1024
16 = 1080i
2 = 852 x 480
7 = 1280 x 1024
12 = 1400 x 1050
17 = 1080p
3 = 1024 x 768
8 = 1360 x 765
13 = 480p
18 = 1280 x 800
4 = 1024 x 852
9 = 1365 x 768
14 = 576p
19 = 1440 x 900
X(
= Refresh rate
0 = 50 Hz
3 = 96 Hz
1 = 60 Hz
4 = 100 Hz
2 = 72 Hz
5 = 120 Hz
+800.633.9876
Inside USA/Canada
Only
+1.714.491.1500
+1.714.491.1517 FAX
Extron USA - East
+800.633.9876
Inside USA/Canada
Only
+1.919.863.1794
+1.919.863.1797 FAX
Extron Europe
+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+800.7339.8766
Inside Asia Only
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+400.883.1568
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.2991800
+971.4.2991880 FAX
© 2011 Extron Electronics. All rights reserved.
GSS 100 • Setup Guide