Extron Electronics DVS 510 Series Setup Guide User Manual
Dvs 510 series • setup guide, Rear panel features and connections, Installation steps
Product Category
1
DVS 510 Series • Setup Guide
The Extron DVS 510 Series scalers are 10-input, multi-format presentation switching scalers that accept and scale DVI,
RGB, YUVp/HDTV, YUVi, S-video, and composite video signals to a common high-resolution output rate. Two models are
available: the standard DVS 510, which has fixed and variable line level audio outputs, and the DVS 510 SA, which adds an
integrated stereo amplifier. Control options include front panel buttons and knobs, Ethernet, RS-232 or RS-422, web pages,
and infrared (IR). This guide provides instructions for an experienced installer to install and connect the DVS 510 scalers.
NOTE: For full installation, configuration, and operation details, see the DVS 510 Series User Guide, available at
Rear Panel Features and Connections
100-240V 50-60 Hz
2A MAX
LAN
RESET
RS232
VID
VID
YC
RGB/R-Y, Y, B-Y
YC
DVI-I
DVI-D
AMPLIFIED
DVI-I
1
2
3
4
5
6
7/8
9/10
V
I
D
E
O
I
N
P
U
T
V
I
D
E
O
O
U
T
P
U
T
A
U
D
I
O
I
N
P
U
T
A
U
D
I
O
O
U
T
P
U
T
1
L
R
L
R
VARIABLE
FIXED
3
L
R
5
L
R
7
L
R
9
L
R
2
L
R
4
L
R
6
L
R
8
L
R
10
L
R
RGB/R-Y, Y, B-Y
L
R
L
R
RGB/R-Y, Y, B-Y
RGB/R-Y, Y, B-Y
10
9
1
4
5
6
8
7
11
12
13
14
15
2
3
a
AC power connector
h
Audio input connectors
b
Video inputs 1 and 2: Composite video
i
Amplified audio output connector (DVS 510 SA only)
c
Video inputs 3 and 4: S-video
j
Variable audio output connector
d
Video inputs 5 and 6: RGB or YUV component
k
Fixed audio output connector
e
Video inputs 7/8 and 9/10: RGB or YUV (7 and 9) and
l
Reset LED
DVI
(8
and
10)
m
Reset button
f
Buffered RGB/YUV output connectors
n
LAN connector
g
DVI-I output connector (digital output only)
o
RS-232/RS-422 connector
Installation Steps
1.
Disconnect power from all equipment.
2.
(Optional) Mount the unit. Rack mount the scaler using the
attached brackets (see the illustration at right). For tabletop
placement, remove the brackets from the right and left sides
and attach the provided rubber feet.
3.
Connect video inputs. Connect video input devices to the
appropriate connectors in the rear panel Video Input section
(
b
through
e
in the diagram above).
z
Video inputs 5 and 6: RGB or YUV component —
Connect one or two RGBHV, RGBS, RGsB, RGBcvS, YUVi,
or YUVp/HDTV video sources to these female 15-pin HD
connectors (shown below). These connectors feature EDID
emulation.
NOTE: (Optional) To obtain one or two more RGB/YUV inputs, you can connect an Extron DVIIM-VGAF/DVIIF
DVI and Analog Breakaway (Y) cable to either or both DVI-I input connectors. Each Y cable provides an
additional RGB VGA connector and DVI-I connector (see ”Breakaway cable” on the next page).
1
2
13
3
14
Inputs 5 and 6
MBD 249
2U Rack Mounting
Bracket (Pre-attached)