Asus NCL-DS1R1 - Manual (Page 90)

4 - 2 8 4 - 2 8 4 - 2 8 4 - 2 8 4 - 2 8 C h a p t e r 4 : B I O S s e t u p C h a p t e r 4 : B I O S s e t u p C h a p t e r 4 : B I O S s e t u p C h a p t e r 4 : B I O S s e t u p C h a p t e r 4 : B I O S s e t u p
Power Management [Enabled] Power Management [Enabled] Power Management [Enabled] Power Management [Enabled] Power Management [Enabled]
Allows you to enable or disable the motherboard Advance Power
Management (APM) feature. Configuration options: [Enabled] [Disabled]
Video Power Down Mode [Suspend] Video Power Down Mode [Suspend] Video Power Down Mode [Suspend] Video Power Down Mode [Suspend] Video Power Down Mode [Suspend]
Allows you to select the video power down mode
Configuration options: [Disabled] [Standby] [Suspend]
Hard Disk Power Down Mode [Suspend] Hard Disk Power Down Mode [Suspend] Hard Disk Power Down Mode [Suspend] Hard Disk Power Down Mode [Suspend] Hard Disk Power Down Mode [Suspend]
Allows you to select the hard disk power down mode
Configuration options: [Disabled] [Standby] [Suspend]
Suspend Time Out [Disabled] Suspend Time Out [Disabled] Suspend Time Out [Disabled] Suspend Time Out [Disabled] Suspend Time Out [Disabled]
Allows you to select the specified time at which the system goes on
suspend mode. Configuration options: [Disabled] [1 Min] [2 Min] [4 Min]
[8 Min] [10 Min] [20 Min] [30 Min] [40 Min] [50 Min] [60 Min]
Throttle Slow Clock Ratio [50%] Throttle Slow Clock Ratio [50%] Throttle Slow Clock Ratio [50%] Throttle Slow Clock Ratio [50%] Throttle Slow Clock Ratio [50%]
Allows you to select duty cycle in throttle mode.
Configuration options: [87.5%] [75.0%] [62.5%] [50.0%] [37.5%]
[25.0%] [12.5%]
Power Button Mode [On/Off] Power Button Mode [On/Off] Power Button Mode [On/Off] Power Button Mode [On/Off] Power Button Mode [On/Off]
Allows the system to go into On/Off mode or suspend mode when the
power button is pressed. Configuration options: [On/Off] [Suspend]
Restore on AC Power Loss [Power Off] Restore on AC Power Loss [Power Off] Restore on AC Power Loss [Power Off] Restore on AC Power Loss [Power Off] Restore on AC Power Loss [Power Off]
When set to Power Off, the system goes into off state after an AC power
loss. When set to Power On, the system goes on after an AC power loss.
When set to Last State, the system goes into either off or on state,
whatever the system state was before the AC power loss.
Configuration options: [Power Off] [Power On] [Last State]
Power On By PS/2 Keyboard [Disabled] Power On By PS/2 Keyboard [Disabled] Power On By PS/2 Keyboard [Disabled] Power On By PS/2 Keyboard [Disabled] Power On By PS/2 Keyboard [Disabled]
Allows you to use specific keys on the keyboard to turn on the system.
This feature requires an ATX power supply that provides at least 1A on the
+5VSB lead. Configuration options: [Disabled] [Enabled]
Power On By PS/2 Mouse [Disabled] Power On By PS/2 Mouse [Disabled] Power On By PS/2 Mouse [Disabled] Power On By PS/2 Mouse [Disabled] Power On By PS/2 Mouse [Disabled]
When set to [Enabled], this parameter allows you to use the PS/2 mouse
to turn on the system. This feature requires an ATX power supply that
provides at least 1A on the +5VSB lead. Configuration options: [Disabled]
[Enabled]