Asus NCL-DS1R1 - Manual (Page 49)

A S U S N C L - D S 1 S e r i e s A S U S N C L - D S 1 S e r i e s A S U S N C L - D S 1 S e r i e s A S U S N C L - D S 1 S e r i e s A S U S N C L - D S 1 S e r i e s 2 - 2 9 2 - 2 9 2 - 2 9 2 - 2 9 2 - 2 9
3 . 3 . 3 . 3 . 3 . S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 ) S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 ) S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 ) S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 ) S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 )
These connectors are for the Serial ATA signal cables for Serial ATA
hard disk drives.
If you installed Serial ATA hard disk drives, you can create a RAID 0 or
RAID 1 configuration with the Intel
® Matrix Storage Technology
through the onboard Intel ® ICH5R integrated RAID controller.
These connectors are set to S t a n d a r d I D E S t a n d a r d I D E S t a n d a r d I D E S t a n d a r d I D E S t a n d a r d I D E mode by default. In
S S S S S t a n d a r d I D E t a n d a r d I D E t a n d a r d I D E t a n d a r d I D E t a n d a r d I D E mode, you can connect Serial ATA boot/data hard disk
drives to these connectors. If you intend to create a Serial ATA RAID set
using these connectors, set the C o n f i g u r e S A T A A s
C o n f i g u r e S A T A A s C o n f i g u r e S A T A A s C o n f i g u r e S A T A A s C o n f i g u r e S A T A A s item in the BIOS
to [RAID]. See section “4.3.6 IDE Configuration” on page 4-15 for details.
I m p o r t a n t n o t e s o n S e r i a l A T A I m p o r t a n t n o t e s o n S e r i a l A T A I m p o r t a n t n o t e s o n S e r i a l A T A I m p o r t a n t n o t e s o n S e r i a l A T A I m p o r t a n t n o t e s o n S e r i a l A T A
• You must install Windows ® 2000 Service Pack 4 or the Windows ® XP
Service Pack 1 before using Serial ATA hard disk drives. The Serial
ATA RAID feature (RAID 0/RAID 1) is available only if you are using
Windows
® 2000/XP.
• Use only two Serial ATA RAID connectors for each RAID 0 or RAID 1
set.
• When using the connectors in S S S S S tandard IDE t a n d a r d I D E t a n d a r d I D E t a n d a r d I D E t a n d a r d I D E mode, connect the
primary (boot) hard disk drive to the SATA1 or SATA2 connector.
Refer to the table below for the recommended SATA hard disk drive
connections.
Serial ATA hard disk drive connection Serial ATA hard disk drive connection Serial ATA hard disk drive connection Serial ATA hard disk drive connection Serial ATA hard disk drive connection
C o n n e c t o r C o n n e c t o r C o n n e c t o r C o n n e c t o r C o n n e c t o r S e t t i n g S e t t i n g S e t t i n g S e t t i n g S e t t i n g U s e U s e U s e U s e U s e
S A T A 1 S A T A 1 S A T A 1 S A T A 1 S A T A 1 M a s t e r M a s t e r M a s t e r M a s t e r M a s t e r B o o t d i s k B o o t d i s k B o o t d i s k B o o t d i s k B o o t d i s k
S A T A 2 S A T A 2 S A T A 2 S A T A 2 S A T A 2 S l a v e S l a v e S l a v e S l a v e S l a v e D a t a d i s k D a t a d i s k D a t a d i s k D a t a d i s k D a t a d i s k
SATA2 SATA1
NCL-DS1 Series SATA connectors
GND RSA
TA_TXP1
RSA
TA_TXN1
GND RSA
TA_RXN1
RSA
TA_RXP1
GND GND RSA
TA_TXP2
RSA
TA_TXN2
GND RSA
TA_RXN2
RSA
TA_RXP2
GND