Asus NCT-D - Manual (Page 50)

2 - 2 8 2 - 2 8 2 - 2 8 2 - 2 8 2 - 2 8 C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n
4 . 4 . 4 . 4 . 4 . S e r i a l A T A R A I D c o n n e c t o r s ( 7 - p i n S A T A _ R A I D 1 , S e r i a l A T A R A I D c o n n e c t o r s ( 7 - p i n S A T A _ R A I D 1 , S e r i a l A T A R A I D c o n n e c t o r s ( 7 - p i n S A T A _ R A I D 1 , S e r i a l A T A R A I D c o n n e c t o r s ( 7 - p i n S A T A _ R A I D 1 , S e r i a l A T A R A I D c o n n e c t o r s ( 7 - p i n S A T A _ R A I D 1 ,
S A T A _ R A I D 2 , S A T A _ R A I D 3 , S A T A _ R A I D 4 )
S A T A _ R A I D 2 , S A T A _ R A I D 3 , S A T A _ R A I D 4 ) S A T A _ R A I D 2 , S A T A _ R A I D 3 , S A T A _ R A I D 4 ) S A T A _ R A I D 2 , S A T A _ R A I D 3 , S A T A _ R A I D 4 ) S A T A _ R A I D 2 , S A T A _ R A I D 3 , S A T A _ R A I D 4 )
These connectors are for Serial ATA signal cables. These connectors
support up to four Serial ATA hard disk drives that you can configure
as a disk array through the optional SATA RAID controller.
Before creating a RAID set using Serial ATA hard disks, make sure that
you have connected the Serial ATA signal cable and installed Serial ATA
hard disk drives; otherwise, you cannot enter the RAID utility and SATA
BIOS setup during POST.
5 . 5 . 5 . 5 . 5 . H a r d d i s k a c t i v i t y L E D c o n n e c t o r ( 2 - p i n H D L E D ) H a r d d i s k a c t i v i t y L E D c o n n e c t o r ( 2 - p i n H D L E D ) H a r d d i s k a c t i v i t y L E D c o n n e c t o r ( 2 - p i n H D L E D ) H a r d d i s k a c t i v i t y L E D c o n n e c t o r ( 2 - p i n H D L E D ) H a r d d i s k a c t i v i t y L E D c o n n e c t o r ( 2 - p i n H D L E D )
This connector supplies power to the hard disk activity LED. The read
or write activities of any device connected to the primary/secondary
IDE connectors or the SATA connectors cause this LED to light up.
NCT-D
GND
RSA
T A_TXP2
RSA
T
A_TXN2
GND
RSA
T A_RXN2
RSA
T A_RXP2
GND
SATA_RAID1
GND
RSA
T A_TXP1
RSA
T
A_TXN1
GND
RSA
T A_RXN1
RSA
T A_RXP1
GND
SATA_RAID2
SATA_RAID3 SATA_RAID4
NCT-D SATA RAID connectors
GND
RSA
T
A_TXP4
RSA
T A_TXN4
GND
RSA
T
A_RXN4
RSA
T A_RXP4
GND GND
RSA
T A_TXP3
RSA
T A_TXN3
GND
RSA
T
A_RXN3
RSA
T
A_RXP3
GND
NCT-D
NCT-D SCSI/SATA card activity LED connector
HDLED
1
ADD_IN_CARD_ACT#
NC
NC
ADD_IN_CARD_ACT#