Theatre Solution Teatro C3 - Manual (Page 3)

Teatro C3 Specifications – Theatre Seating
Page 3 of 4
D. Armrests: Shall be kiln-dried solid hardwood, nominally 1” thick x 2-1/2” wide x 12” long, stained to
match the outer seat and back panels. The armrest will be fastened to the steel frame arm support with
one 10-24 x 7/8” flat head machine screw and one 10-24 x 2-1/4” flat head machine screw into threaded
inserts on the underside of the armrest. Chairs equipped with tablet arms shall have armrests nominally
1” thick x 2-1/2” wide x 18” long and shall be attached to the steel frame arm support with four #8 x 3/4”
sheet metal screws.
E. Hinge: The seat hinge shall be a weldment consisting of a 7 gauge hot-rolled pickled-in-oil steel
component and shall be formed and punched to receive a 0.56” id x 0.75” od x 0.5” long steel bushing.
A self-lubricating nylon sleeve shall be fitted between the seat hinge and the standard seat hinge pin.
The hinge shall be machined to provide a positive stop location for the seat in both occupied and
unoccupied positions. The hinge shall be fitted with a plastic cover to eliminate all pinch points and shall
include a 3/16” thick urethane rubber pad to dampen noise upon the seat return to the vertical position.
PART 3 – OPTIONS
3.1 END PANEL
A. Provide manufacturer’s standard end panel at the end of the row. The configuration of the panel shall
follow the angle of the frame and back at the rear, and shall be vertical at the front end. The panel shall be
constructed of 3/4” thick plywood with veneer on both sides and 1/8” thick solid wood on the vertical edges.
The end panel shall be stained to match the outer wood seat, back, and armrests.
3.2 AISLE LIGHT
A. Aisle lights shall be provided in accordance to the locations shown on the architectural drawings. The units
shall be of low voltage (24v) type and the light tube shall fit into a routed area on the underside of the
armrest. The chair frame shall be prepared to accept the power wire. The necessary access holes and
blank cover plates shall be provided. The chair manufacturer shall also provide the necessary
transformers. All wiring and electrical connections shall be conducted at the job site and shall be the
responsibility of others.
3.3 SEAT AND ROW IDENTIFICATION TAGS
A. Provide manufacturer’s standard shape brass number and letter plates. Font shall be Times Roman. The
size of the font on the seat number plates shall be 27pt; the size of the font on the row letter plates shall be
42pt. The number plates shall fit into a recessed area at the top edge of the seat. The row letter plates
shall fit into a recessed area at the back of the armrest.
3.4 REMOVABLE CHAIR
A. Provide manufacturer’s standard one, two, or three chair removable units which shall include an integrated
steel sled-base that is engineered to conform to the row radii and includes two through holes per chair for
floor mounting.
3.5 FREESTANDING REMOVABLE CHAIR
A. Provide manufacturer’s standard freestanding removable chair which shall include an integrated steel sled-
base that is engineered to conform to the row radii and includes extended length floor plates to allow the
chairs to remain stable with no physical attachment to the floor.
3.6 TABLET ARMS
A. Tablet arm shall be two-motion fold-away style, constructed of 1/2” medium density fiberboard, faced two
sides with matte black high-pressure laminate. The edges shall be finished with a vinyl T-molding trimmed
flush with both top and bottom surfaces.
3.7 POWER/DATA
A. Where indicated on the drawings, chair frames shall be equipped with a 115v/15amp power outlet and a
RJ-45 Category 6 data port located on the front of the armrest gusset. Wire raceways shall be provided for
routing of the wires from chair to chair. All wiring and electrical connections shall be conducted at the job
site and shall be the responsibility of others.
3.8 BOOKRACKS
A. The bookrack shall be constructed of hardwoods and hardwood plywood. Bookrack shall be assembled with
tongue and groove construction and finished with a catalyzed lacquer. The bookrack shall be attached to
the outer surface of the chair back. An optional attachment configuration shall consist of a steel weldment
attached to the chair leg. This configuration allows the bookrack to be located between chair backs.