Rainbow Electronics MAX984 - Manual (Page 2)

MAX971–MAX974/MAX981–MAX984
Ultra-Low-Power, Open-Drain,
Single/Dual-Supply Comparators
2 _______________________________________________________________________________________
V+ to V-, V+ to GND, GND to V-................................-0.3V, +12V
Inputs
Current: IN_+, IN_-, HYST..............................................20mA
Voltage: IN_+, IN_-, HYST ...............(V+ + 0.3V) to (V- - 0.3V)
Outputs
Current: REF...................................................................20mA
OUT_ ................................................................50mA
Voltage: REF ....................................(V+ + 0.3V) to (V- - 0.3V)
OUT_ (MAX9_1/9_4) ...............+12V to (GND - 0.3V)
(MAX9_2/9_3) ....................+12V to (V- - 0.3V)
OUT_ Short-Circuit Duration ..................................Continuous
Continuous Power Dissipation (T A = +70°C)
8-Pin Plastic DIP (derate 9.09mW/°C above +70°C) ...727mW
8-Pin SO (derate 5.88mW/°C above +70°C)................471mW
8-Pin µMAX (derate 4.1mW/°C above +70°C) .............330mW
8-Pin CERDIP (derate 8.00mW/°C above +70°C)........640mW
16-Pin Plastic DIP (derate 10.53mW/°C above +70°C)..842mW
16-Pin SO (derate 8.70mW/°C above +70°C) ................696mW
16-Pin CERDIP (derate 10.00mW/°C above +70°C) ......800mW
Operating Temperature Ranges
MAX97_C_ _/MAX98_C_ _ ..................................0°C to +70°C
MAX97_E_ _/MAX98_E_ _ ...............................-40°C to +85°C
MAX97_MJ_/MAX98_MJ_ .............................-55°C to +125°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10sec) .............................+300°C
ELECTRICAL CHARACTERISTICS: 5V OPERATION
(V+ = 5V, V- = GND = 0V, T A = T MIN to T MAX , unless otherwise noted. Typical values are at T A = +25°C.)
PARAMETER
MAX982/
MAX9_3,
HYST = REF
MIN TYP MAX UNITS
MAX9_4
7.5
V V- V+ - 1.3
5.5 6.5
MAX9_1,
HYST = REF
8.5
Supply Current IN+ = IN- + 100mV
IN+ = IN- = 2.5V
11
µA
Supply Voltage Range
T A = +25°C, 100pF load,
1M Ω pull-up to V+
2.5 11 V
2.5 3.2
MAX972
4
5
2.5 3.2
Input Offset Voltage
CONDITIONS
M temp. range
±10 mV
T A = +25°C
C/E temp. ranges
M temp. range
±0.01 ±5
nA Input Leakage Current (IN-, IN+)
(Note 1)
±40
Input Leakage Current (HYST)
T A = +25°C
C/E temp. ranges
M temp. range
±0.02 nA
Input Common-Mode Voltage Range
T A = +25°C
V CM = 2.5V
C/E temp. ranges
Common-Mode Rejection Ratio
M temp. range
MAX9_1/MAX982/MAX9_3
0.1 1.0 mV/V
Power-Supply Rejection Ratio
V- to (V+ - 1.3V)
V+ = 2.5V to 11V
100Hz to 100kHz
0.1 1.0 mV/V
Voltage Noise
MAX9_1/MAX982/MAX9_3
Overdrive = 10mV
Overdrive = 100mV
20 µV RMS
Hysteresis Input Voltage Range REF - 0.05 REF V
C/E temp. ranges
M temp. range
T A = +25°C
12
µs
Response Time
(high-to-low transition)
C/E temp. ranges
4
4
5
3.1 4.5
6
Output Voltage Range 0 11 V
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ABSOLUTE MAXIMUM RATINGS
T A = +25°C, 100pF load, 1M Ω pull-up to V+ 300 µs
Response Time
(low-to-high transition) (Note 2)
POWER REQUIREMENTS
COMPARATOR