Wilwood Dynapro 6 Big Brake Front Brake Kit (Hub) - Manual (Page 2)

1
2
2A
3
4
5
6
6A
7
8
9
10
11
12
12A
12B
13
14
15
16
17
18
19
19A
20
21
22
23
24
25
26
1
2
2
2
2
6
2
2
10
2
2
2
2
2
2
2
16
10
2
2
2
2
2
2
4
4
16
1
2
2
2
249-10433/34
240-0976
300-3415
240-1347
230-10899
240-7096
230-10421
230-10422
230-2187
270-7274
370-0879
380-0927
300-3099
160-5843
160-7103/04
160-7103/04-BK
230-11934
230-11239
370-0877
240-9499
270-2158
211-1674
120-10122/23
120-10122/23-RD
240-10190
230-10025
240-1159
150-10006K
300-7316
240-11102
230-0819 Brackets, Caliper Mounting (pair, one each, left and right)
Washer, 1/2 x .09 inch Thick
Spacer, 1 x .493 inch Thick (use with disc brake spindle only)
Washer, 1/2 x .015 inch Thick
Bolt, 1/2-20 x 2.75 Long, Hex Head
Washer, 5/8 x .05 inch Thick
Bolt, 5/8 x 18 x 1.12 Long, Flat Head
Bolt, 5/8 x 18 x 1.62 Long, Flat Head (use with disc brake spindle only)
Stud, 1/2-20 x 1.75 Long, 12 Point
Hub Assembly
Cone, Inner Bearing
Seal, Grease
Adapter, Rotor
Rotor, .81” Thick x 12.19” Dia, 8 x 7.00” Bolt Circle
Rotor, Zinc, Drilled and Slotted (pair, one each, left and right)
Rotor, Black, Drilled and Slotted (pair, one each, left and right)
Bolt, 5/16-18 x 0.75 Long, Torx Button Head
Bolt, 3/8-16 x 1.0 Long, Torx Button Head
Cone, Outer Bearing
Washer, Spindle
Cap, Dust
O-ring
Caliper, DynaPro 6
Caliper, DynaPro 6, Red
Washer, .391 I.D. x .625 O.D. x .063 Thick
Bolt, 3/8-24 x 1.25 Long, Hex Head
Shim, 0.032 inch Thick
Pad, BP-10, Axle Set
Clip, Pad Retainer
Washer, .515 I.D. x .875 O.D. x .063 Thick
Nut, 1/2-20 Hex
ITEM NO. PART NO. DESCRIPTION QTY
NOTES:
Part Number 230-10435 Bolt Kit, caliper mounting bracket to spindle, included part numbers 230-0819,230-10899, 230-10421,
230-10422, 240-0976, 240-1347, 240-7096, 240-11102 and 300-3415
Part Number 230-3829 Bolt Kit, adapter plate to hub, includes part number 230-11239
Part Number 230-12120 Bolt Kit, rotor to adapter plate, includes part number 230-11834
Part Number 230-11861 Bolt Kit, caliper to bracket, includes part numbers 230-10025, 240-10190 and 240-1159
Items 2A and 6A are to be used with Disc Brake Spindles
Item 12A is an optional item and is included in the (Z) drilled zinc kits. Add -Z to end of part number when ordering.
Item 12B is an optional item and is included in the (D) drilled black kits. Add -D to end of part number when ordering.
Item 19A is an optional item and is included in the (R) red kits. Add -R to end of part number when ordering.
Parts List
Important Notice - Read This First
Before any tear-down or disassembly begins, review the following information:
• Review the wheel clearance diagram (figure 2, page 3) to verify that there is adequate clearance with the
wheels you will be using with the installation.
• Front brake kits do not include flex lines. OEM brake lines will not adapt to Wilwood calipers. Check the
assembly instructions, or associated components section for brake line recommendations before assembly.
In addition, Wilwood offers an extensive listing of brake lines and fittings on our web site:
www.wilwood.com .
• Due to OEM production differences and other variations from vehicle to vehicle, the fastener hardware and
other components in this kit may not be suitable for a specific application or vehicle.
• It is the responsibility of the purchaser and installer of this kit to verify suitability / fitment of all components
and ensure all fasteners and hardware achieve complete and proper engagement. Improper or inadequate
engagement can lead to component failure.
Page 2
Photographic Tip
Important and highly recommended: Take photos of brake system before disassembly and during the disassembly process. In the
event, trouble-shooting photos can be life savers. Many vehicles have undocumented variations, photos will make it much simpler for
Wilwood to assist you if you have a problem.