Milton CAT 160M - Manual (Page 22)

22 160M Motor Grader specifications
Tandems
Height 572 mm 22.5 in
Width 204 mm 8 in
Sidewall Thickness – Inner 25 mm 1 in
Sidewall Thickness – Outer 18 mm 0.7 in
Drive Chain Pitch 50.8 mm 2 in
Wheel Axle Spacing 1523 mm 60 in
Tandem Oscillation – Front Up 15°
Tandem Oscillation – Front Down 25°
Moldboard
Moldboard – Width 4.3 m 14 ft
Moldboard – Height 686 mm 27 in
Moldboard – Thickness 25 mm 1 in
Arc Radius 413 mm 16.3 in
Throat Clearance 95 mm 3.7 in
Cutting Edge – Width 152 mm 6 in
Cutting Edge – Thickness 16 mm 0.6 in
End Bit – Width 152 mm 6 in
End Bit – Thickness 16 mm 0.6 in
Blade Pull – Base GVW 10 362 kg 22,845 lb
Blade Pull – Max GVW 14 009 kg 30,885 lb
Blade Pull – Base GVW (AWD) 14 925 kg 32,904 lb
Blade Pull – Max GVW (AWD) 18 366 kg 40,490 lb
Down Pressure – Base GVW 7756 kg 17,100 lb
Down Pressure – Max GVW 14 812 kg 32,654 lb
• Blade pull calculated at 0.9 traction coefficient, which is equal
to ideal no-slip conditions, and Gross Machine Weight.
Blade Range
Circle Centershift – Right 728 mm 28.7 in
Circle Centershift – Left 695 mm 27.4 in
Moldboard Sideshift – Right 950 mm 37.4 in
Moldboard Sideshift – Left 820 mm 32.3 in
Maximum Blade Position Angle 90°
Blade Tip Range – Forward 40°
Blade Tip Range – Backward 5°
Maximum Shoulder Reach Outside of Tires
– Right 2278 mm 89.7 in
– Left 2090 mm 82.3 in
Maximum Lift Above Ground 452 mm 17.8 in
Maximum Depth of Cut 750 mm 29.5 in
Operating Specifications
Top Speed – Fwd. 47.4 km/h 29.5 mph
Top Speed – Rev. 37.4 km/h 23.3 mph
Turning Radius, Outside Front Tires 7.6 m 24 ft 11 in
Steering Range – Left/Right 47.5°
Articulation Angle – Left/Right 20°
Fwd. 1st 4.1 km/h 2.5 mph
Fwd. 2nd 5.6 km/h 3.5 mph
Fwd. 3rd 8.1 km/h 5 mph
Fwd. 4th 11.2 km/h 7 mph
Fwd. 5th 17.4 km/h 10.8 mph
Fwd. 6th 23.7 km/h 14.7 mph
Fwd. 7th 32.6 km/h 20.3 mph
Fwd. 8th 47.4 km/h 29.5 mph
Rev. 1st 3.3 km/h 2 mph
Rev. 2nd 6.1 km/h 3.8 mph
Rev. 3rd 8.8 km/h 5.5 mph
Rev. 4th 13.7 km/h 8.5 mph
Rev. 5th 25.7 km/h 16 mph
Rev. 6th 37.4 km/h 23.3 mph
Service Refill
Fuel Capacity 398 L 105 gal
Cooling System 40 L 10.6 gal
Hydraulic System – Tank 64 L 16.9 gal
Engine Oil 30 L 7.9 gal
Trans./Diff./Final Drives 65 L 17.2 gal
Tandem Housing (each) 80 L 21.1 gal
Front Wheel Spindle 0.5 L 0.13 gal
Bearing Housing
Circle Drive Housing 7 L 1.8 gal
Frame
Circle – Diameter 1553 mm 61.1 in
Circle – Blade Beam Thickness 40 mm 1.6 in
Drawbar – Height 152 mm 6 in
Drawbar – Width 76.2 mm 3 in
Front Frame Structure
– Height 305 mm 12 in
– Width 305 mm 12 in
– Thickness 16 mm 0.6 in
Front Axle
– Height to Center 571 mm 22.5 in
– Wheel Lean, Left/Right 18°
– Total Oscillation Per Side 32°