C&H Technology CM300DY-24H - Manual (Page 3)

CM300DY-24H
Dual IGBTMOD™ H-Series Module
300 Amperes/1200 Volts
Rev. 5/07
Powerex, Inc., 173 Pavilion Lane, Youngwood, Pennsylvania 15697 (724) 925-7272
Absolute Maximum Ratings, T
j
= 25°C unless otherwise specified
Ratings Symbol CM300DY-24H Units
Junction Temperature T
j
–40 to 150 °C
Storage Temperature T
stg
–40 to 125 °C
Collector-Emitter Voltage (G-E SHORT) V
CES
1200 Volts
Gate-Emitter Voltage V
GES
±20 Volts
Collector Current I
C
300 Amperes
Peak Collector Current I
CM
600* Amperes
Diode Forward Current I
F
300 Amperes
Diode Forward Surge Current I
FM
600* Amperes
Power Dissipation P
d
2100 Watts
Max. Mounting Torque M6 Terminal Screws – 26 in-lb
Max. Mounting Torque M6 Mounting Screws – 26 in-lb
Module Weight (Typical) – 500 Grams
V Isolation V
RMS
2500 Volts
* Pulse width and repetition rate should be such that device junction temperature does not exceed the device rating.
Static Electrical Characteristics, T
j
= 25 °C unless otherwise specified
Characteristics Symbol Test Conditions Min. Typ. Max. Units
Collector-Cutoff Current I
CES
V
CE
= V
CES
, V
GE
= 0V – – 1.0 mA
Gate Leakage Current I
GES
V
GE
= V
GES
, V
CE
= 0V – – 0.5 μ A
Gate-Emitter Threshold Voltage V
GE(th)
I
C
= 30mA, V
CE
= 10V 4.5 6.0 7.5 Volts
Collector-Emitter Saturation Voltage V
CE(sat)
I
C
= 300A, V
GE
= 15V – 2.5 3.2** Volts
I
C
= 300A, V
GE
= 15V, T
j
= 150°C – 2.25 – Volts
Total Gate Charge Q
G
V
CC
= 600V, I
C
= 300A, V
GS
= 15V – 1500 – nC
Diode Forward Voltage V
FM
I
E
= 300A, V
GS
= 0V – – 3.5 Volts
** Pulse width and repetition rate should be such that device junction temperature rise is negligible.
Dynamic Electrical Characteristics, T
j
= 25 °C unless otherwise specified
Characteristics Symbol Test Conditions Min. Typ. Max. Units
Input Capacitance C
ies
– – 60 nF
Output Capacitance C
oes
V
GE
= 0V, V
CE
= 10V, f = MHz – – 21 nF
Reverse Transfer Capacitance C
res
– – 12 nF
Resistive Turn-on Delay Time t
d(on)
– – 250 ns
Load Rise Time t
r
V
CC
= 600V, I
C
= 300A, – – 500 ns
Switching Turn-off Delay Time t
d(off)
V
GE1
= V
GE2
= 15V, R
G
= 1.0 Ω – – 350 ns
Times Fall Time t
f
– – 350 ns
Diode Reverse Recovery Time t
rr
I
E
= 300A, di
E
/dt = –600A/ μ s – – 250 ns
Diode Reverse Recovery Charge Q
rr
I
E
= 300A, di
E
/dt = –600A/ μ s – 2.23 – μ C
Thermal and Mechanical Characteristics, T
j
= 25 °C unless otherwise specified
Characteristics Symbol Test Conditions Min. Typ. Max. Units
Thermal Resistance, Junction to Case R
th(j-c)
Per IGBT – – 0.06 °C/W
Thermal Resistance, Junction to Case R
th(j-c)
Per FWDi – – 0.12 °C/W
Contact Thermal Resistance R
th(c-f)
Per Module, Thermal Grease Applied – – 0.035 °C/W