VEGA VEGAPULS 66 (≥ 2.0.0 - ≥ 4.0.0) enamel Modbus and Levelmaster protocol User Manual

Operating instructions, Vegapuls 66 enamel

Text mode
Original mode

Operating Instructions

Radar sensor for continuous level

measurement of liquids

VEGAPULS 66 enamel

Modbus and Levelmaster protocol

Document ID: 41368

Table of contents

Document Outline

Quick start
1 About this document
- 1.1 Function
- 1.2 Target group
- 1.3 Symbolism used
2 For your safety
- 2.1 Authorised personnel
- 2.2 Appropriate use
- 2.3 Warning about incorrect use
- 2.4 General safety instructions
- 2.5 CE conformity
- 2.6 NAMUR recommendations
- 2.7 Radio license for Europe
- 2.8 Radio license for USA/Canada
- 2.9 Environmental instructions
3 Product description
- 3.1 Configuration
- 3.2 Principle of operation
- 3.3 Packaging, transport and storage
- 3.4 Accessories and replacement parts
4 Mounting
- 4.1 General instructions
- 4.2 Instructions for installation
5 Connecting to power supply and bus system
- 5.1 Preparing the connection
- 5.2 Connecting
- 5.3 Wiring plan, double chamber housing
- 5.4 Switch-on phase
6 Set up the sensor with the indicating and adjustment module
- 6.1 Insert indicating and adjustment module
- 6.2 Adjustment system
- 6.3 Parameter adjustment
- 6.4 Saving the parameter adjustment data
7 Setting up sensor and Modbus interface with PACTware
- 7.1 Connect the PC
- 7.2 Parameter adjustment with PACTware
- 7.3 Saving the parameter adjustment data
8 Set up with other systems
- 8.1 DD adjustment programs
- 8.2 Communicator 375, 475
9 Diagnosis, Asset Management and service
- 9.1 Maintenance
- 9.2 Measured value and event memory
- 9.3 Asset Management function
- 9.4 Rectify faults
- 9.5 Exchanging the electronics module
- 9.6 Software update
- 9.7 How to proceed in case of repair
9.4 Measurement error with constant level
9.4 Measurement error during filling
9.4 Measurement error during emptying
10 Dismounting
- 10.1 Dismounting steps
- 10.2 Disposal
11 Supplement
- 11.1 Technical data
- 11.2 Basics Modbus
- 11.3 Modbus register
- 11.4 Modbus RTU commands
- 11.5 Levelmaster commands
- 11.6 Configuration of typical Modbus hosts
- 11.7 Dimensions
- 11.8 Industrial property rights
- 11.9 Trademark
11.2 Bus description
11.2 Bus architecture
11.2 Protocol description
11.2 Parameters for the bus communication
11.2 General configuration of the host
11.3 Holding Register
11.3 Input register
11.4 FC3 Read Holding Register
11.4 FC4 Read Input Register
11.4 FC6 Write Single Register
11.4 FC8 Diagnostics
11.4 FC16 Write Multiple Register
11.4 FC17 Report Slave ID
11.4 FC43 Sub 14, Read Device Identification
11.5 Parameters for the bus communication
11.5 Report Level (and Temperature)
11.5 Report Unit Number
11.5 Assign Unit Number
11.5 Set number of Floats
11.5 Set Baud Rate
11.5 Set Receive to Transmit Delay
11.5 Report Number of Floats
11.5 Report Receive to Transmit Delay
11.5 Error codes
11.6 Fisher ROC 809
11.6 ABB Total Flow
11.6 Thermo Electron Autopilot
11.6 Bristol ControlWave Micro
11.6 ScadaPack