VTech DS6522-3-32-4 Abridged manual - Manual (Page 11)

Add and register a handset
The handsets provided with your telephone system are already registered. Each
handset is assigned a number that displays on the handset. Additional handsets
registered to the telephone system are assigned numbers in the sequential order.
This telephone system accommodates up to five handsets.
You can add new handsets (
DS6501/DS6501-12/DS6501-15/DS6501-16,
purchased separately) to your telephone system. Each handset must be registered
with the telephone base before use. When first purchased and properly charged,
each expansion handset shows To register HS... and ...see manual alternately.
Charge the handset before registering it to the telephone base.
To register a handset:
Place the new/non-registered handset in the telephone base.
Wait for about 0 seconds. The handset shows Registering... then Registered
and you hear a beep when the registration process completes. The registration
process takes about 90 seconds to complete.
Replace a handset
If you want to replace a handset or reassign the designated handset number of a
registered handset, you must deregister all handsets and then individually register
each handset.
To deregister all handsets:
Press and hold /FIND HANDSET on the telephone base for about 0 seconds
until the IN USE light on the telephone base turns on and starts flashing.
Immediately press /FIND HANDSET again. You must press /FIND HANDSET
while the IN USE light is still flashing. The IN USE light flashes for approximately
five seconds.
All handsets show
To register HS... and ...see manual alternately when the
deregistration process completes. The deregistration process takes about
0 seconds to complete.
Troubleshooting
If you have difficulty with your telephone, please try the suggestions below.
For customer service, visit our website at www.vtechphones.com or call
(800) 595-95. In Canada, go to www.vtechcanada.com or call
(800) 267-7377.
I cannot add and connect my cell phone to the telephone base.
Make sure you have cellular coverage.
Make sure your cell phone is compatible with your DS6520/DS6521/DS6522.
Check the Bluetooth compatibility list at www.vtechphones.com.
Make sure the Bluetooth function of your cell phone is turned on. See the user’s
manual of your cell phone for more information.
Make sure that your Bluetooth cell phone is not connected to any other
Bluetooth device.
To connect your cell phone, make sure that your cell phone is connected and
active on the device list.
Remove VTech DS6520/DS6521/DS6522 from your cell phone’s handsfree
device history list (see the user’s manual of your cell phone for more information).
Carefully follow the pairing instructions on pages 5-6 and make sure that your cell
phone is not connected to any other Bluetooth device.
Turn off your cell phone, then turn it on again.
For some cell phones, you must authorize VTech DS6520/DS6521/DS6522
device in your cell phone’s Bluetooth feature. See the user’s manual of your cell
phone for more information.
Manually connect your cell phone to VTech DS6520/DS6521/DS6522. Refer to
the user’s manual of your cell phone for more information.
Reset the telephone base. Unplug the unit’s electrical power. Wait for
approximately 5 seconds, then plug it back in. Repeat the above suggestions.
I cannot find VTech DS6520/DS6521/DS6522 on my cell phone.
Make sure that the telephone base is in discoverable mode.
Make sure that you manually set your cell phone to search for devices.
Remove VTech DS6520/DS6521/DS6522 from your cell phone’s handsfree
device history list (see the user’s manual of your cell phone).
Turn off your cell phone, then turn it on again.
Reset the telephone base. Unplug the unit’s electrical power. Wait for
approximately 5 seconds, then plug it back in. Repeat the above suggestions.
.
2.
.
2.
3.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Do not place the handset
in the charger.