Milwaukee DD 3 -152 - Manual (Page 33)

30
GB
English English
GB
Always use suitable fixing means (impact anchor, knurled threaded
rod, quick-acting nut) to secure the drill stand to the substrate that is
to be machined.
Perform overhead drilling only with suitable protective appliances
(water catcher).
SPECIFIED CONDITIONS OF USE
The machine is intended for dry drilling in brick and tile and wet drilling
in concrete.
Do not use this product in any other way as stated for normal use.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that the product described
under “Technical Data” fulfills all the relevant regulations and the
directives 2011/65/EU (RoHs), 2004/108/ EC, 2006/42/EC and the
following harmonized standards have been used:
EN 60745-1:2009 + A11:2010
EN 60745-2-1:2010
EN 61029-1:2009
EN 61029-2-6:2010
EN 55014-1:2006 + A1:2009 + A2:2011
EN 55014-2:1997 + A1:2001 + A2:2008
EN 61000-3-2:2006 + A1:2009 + A2:2009
EN 61000-3-3:2008
Winnenden, 2013-03-12
Alexander Krug / Managing Director
Authorized to compile the technical file
Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany
MAINS CONNECTION
Connect only to single-phase AC current and only to the system vol-
tage indicated on the rating plate. It is also possible to connect to sockets
without an earthing contact as the design conforms to safety class II.
WORKING TIPS
To gain a better drill progress take out the centre bit after having reached
a depth of about 10-15 mm. Insert core cutter into the existing groove and
let machine run up smoothly.
Bore-holes which don‘t have to be applied exactly can be drilled without
a centre bit. For that purpose apply the core cutter slantingly and put the
machine slowly straight when a depth of about 5 mm has been reached.
(This is only possible when using short core cutters!)
If drill cores should come loose, take core cutter from the material and
remove drill cores.
For best performance the diamond segments should be „rougheup“ to
expose the fragments of diamond: To expose the diamond fragments rub
surface of segments with stone
WARNING! Read all safety warnings and all instructions,
including those given in the accompanying brochure.
Failure to follow the warnings and instructions may result in electric shock,
fire and/or serious injury.
Save all warnings and instructions for future reference.
SAFETY INSTRUCTIONS FOR DRILLS
Wear ear protectors. Exposure to noise can cause hearing loss.
Use auxiliary handle(s), if supplied with the tool. Loss of control can
cause personal injury.
Hold power tool by insulated gripping surfaces, when performing
an operation where the cutting accessory may contact hidden
wiring or its own cord. Cutting accessory contacting a „live“ wire may
make exposed metal parts of the power tool „live“ and could give the
operator an electric shock.
Use protective equipment. Always wear safety glasses when working
with the machine. The use of protective clothing is recommended, such
as dust mask, protective gloves, sturdy non-slip footwear, helmet and ear
defenders.
Wear protective gloves when replacing the core bit. The core bit can
become hot after prolonged operation of the power tool.
The dust produced when using this tool may be harmful to health. Do not
inhale the dust. Use a dust absorption system and wear a suitable dust
protection mask. Remove deposited dust thoroughly, e.g. with a vacuum
cleaner.
The built-in friction clutch only reacts to jerky locking, which is why you
should always use the additional handle.
Only plug-in when machine is switched off.
Keep mains lead clear from working range of the machine. Always lead the
cable away behind you.
When working in walls ceiling, or floor, take care to avoid electric cables
and gas or waterpipes.
Never operate the machine without the residual current device (PRCD)
provided.
Before use check machine, cable, and plug for any damages or material
fatigue. Repairs should only be carried out by authorised Service Agents.
Damaged mains plugs and cables must be repaired or replaced only
through a Milwaukee after-sales service agent.
Pay attention that neither persons in the working area nor the power tool
itself come into contact with the water that comes out.
After interruption of your work, restart the tool only after having made
sure that the drill bit is moving freely.
Do not use machines on any material containing asbestos.
Never lay the power tool down until the accessory has come to a
complete stop. The spinning accessory may grab the surface and pull
the power tool out of your control.
Examine the core bit before inserting it. Use only core bits that are
in perfect condition. Damaged or deformed core bits can lead to
dangerous situations.
Check the proper seating of the core bit. Incorrectly or insecurely
fastened core bits can become loose during operation and may pose
a danger.
The tool may be used only in two-hand operation or with the drill rig.
Do not expose the drill stand to rain and do not use in damp or non-
flameproof rooms.
Always keep a safe footing and hold machine with both hands. Keep
children or animals away from working area.