Milwaukee WCS 45 - Manual (Page 9)

17 16
.......1900 W
.......5800 min -1
.........150 mm
........0-45 mm
......17-45 mm
..........6,6 kg
..........3,5 m/s 2
...........99 dB (A)
......... 110 dB (A)
ENGLISH
TECHNICAL DATA
Rated input ..............................................................................
No-load speed .........................................................................
Grinding disk diameter.............................................................
Cutting depth ...........................................................................
Cutting width ............................................................................
Weight according EPTA-Procedure 01/2003 ...........................
Typical weighted acceleration in the hand-arm area ...............
Typical A-weighted sound levels:
Sound pressure level (K = 3 dB(A)) ......................................
Sound power level (K = 3 dB(A)) ...........................................
Measured values determined according to EN 60 745.
SAFETY INSTRUCTIONS
WARNING! Read all safety warnings and all
instructions, including those given in the accompanying
brochure. Failure to follow the warnings and instructions
may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
Wear ear protectors. Exposure to noise can cause hearing
loss.
Use auxiliary handles supplied with the tool. Loss of
control can cause personal injury.
Hold power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory
may contact hidden wiring or its own cord. Contact with
a „live“ wire will also make exposed metal parts of the power
tool „live“ and shock the operator.
Appliances used at many different locations including open
air must be connected via a current surge preventing switch.
Always wear goggles when using the machine. It is
recommended to wear gloves, sturdy non slipping shoes
and apron.
Always disconnect the plug from the socket before carrying
out any work on the machine.
Only plug-in when machine is switched off.
Keep mains lead clear from working range of the machine.
Always lead the cable away behind you.
After switching off, the machine will not be idle immediately.
(After-running of the work spindle.) Allow the machine to
come to a stop before putting down.
Never reach into the danger area of the plane when it is
running.
Only use tools whose permitted speed is at least as high as
the highest no-load speed of the machine.
Immediately switch off the machine in case of considerable
vibrations or if other malfunctions occur. Check the machine
in order to find out the cause.
Only use sharpened and flawless diamond cutting discs.
Immediately exchange bent or cracked diamond cutting
discs. Carry out a test run without load for at least 30
seconds.
Only use and store diamond cutting discs according to the
manufacturer‘s instructions.
Pay attention to the dimensions of the cutting discs. The
diameter of the centre hole must fit the flange without play.
Do not use any eduction pieces or adapters.
Only use the machine for dry cutting in stone.
Mind hidden electric lines, gas and water pipes. Check your
working area, e.g. with a metal detector.
The dust that arises when working with this tool can be
detrimental to health and therefore not reach the body. Use
a dust absorption system and wear a suitable dust
protection mask. Remove deposited dust thoroughly, e.g.
with a vacuum cleaner.
MAINS CONNECTION
Connect only to single-phase a.c. current and only to the
system voltage indicated on the rating plate. It is also
possible to connect to sockets without an earthing contact
as the design conforms to safety class II.
Inrush currents cause short-time voltage drops. Under
unfavourable power supply conditions, other equipment may
be affected. If the system impedance of the power supply is
lower than 0,2 Ohm, disturbances are unlikely to occur.
SPECIFIED CONDITIONS OF USE
The wall-chaser machine cuts slots for cables and pipes
(masonry grooves) in any kind of brickwork with two
diamond cutting discs running parallel to each other.
Do not use this product in any other way as stated for
normal use.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product is
in conformity with the following standards or standardized
documents.
EN 60745
EN 55014-1:2006 + A 1:2009 + A2:2011
EN 55014-2:1997 + A1:2001 + A2:2008
EN 61000-3-2:2006 + A1:2009 + A2:2009
EN 61000-3-3:2008
in accordance with the regulations
2011/65/EU (RoHs)
2006/42/EC
2004/108/EC
Winnenden, 2012-09-07
Rainer Kumpf
Director Product Development
Authorized to compile the technical file
ADVICE FOR OPERATION
The machine switches off automatically if the motor is
overloaded. Allow it to cool, press the overload button and
restart the machine. If the overload protection switches it off
frequently, reduce the cutting pressure or depth of cut.
The infinitely variable cutting width setting has the
advantage that, if the groove width is set correctly, pipes etc.
can be fitted precisely into the groove and it is not
necessary to secure them with nails etc. to prevent them
from falling out.
Sharpen blunt diamond cutting blades (can be recognised
by sparks flying while cutting) by making several cuts into
calcareous sandstone or a special sharpening stone.
The Milwaukee diamond cut-off wheels supplied are of an
extremely high quality and enable high cutting performances
ENGLISH
to be achieved in all types of rock and concrete. In the event
of wear we recommend that you replace them with diamond
cut-off wheels from Milwaukee‘s range of accessories.
MAINTENANCE
The ventilation slots of the machine must be kept clear at all
times.
Use only Milwaukee accessories and Milwaukee spare
parts. Should components need to be replaced which have
not been described, please contact one of our Milwaukee
service agents (see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered.
Please state the Article No. as well as the machine type
printed on the label and order the drawing at your local
service agents or directly at: Milwaukee Electric Tool,
Max-Eyth-Straße 10, D-71364 Winnenden, Germany.
SYMBOLS
Please read the instructions carefully before
starting the machine.
Always wear goggles when using the
machine.
Wear ear protectors!
Use an FFP2 particulate respirator as the
minimum amount of protection.
Wear gloves!
Always disconnect the plug from the socket
before carrying out any work on the
machine.
Accessory - Not included in standard
equipment, available as an accessory.
Do not dispose of electric tools together
with household waste material! In
observance of European Directive 2002/96/
EC on waste electrical and electronic
equipment and its implementation in
accordance with national law, electric tools
that have reached the end of their life must
be collected separately and returned to an
environmentally compatible recycling
facility.
Class II construction, tool in which
protection against electric shock does not
rely on basic insulation only, but in which
additional safety precautions, such as
double insulation or reinforced insulation,
are provided.