Yamaha EMX-220VCD - Manual (Page 30)

E-22
VIDEO CD PLAYER OPERATION
STANDBY/ON
TIME
A
PROG
B C D
+ I0
E
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9 0
PRESET
INPUT
TIME INDEX
INTRO DIGEST
KARAOKE SLEEP
VCD/CD
MUSIC
TUNER
PROGRAM
VOLUME
DISC SKIP RETURN PREV NEXT SELECT
STOP PLAY/PAUSE
LEVEL ECHO/KEY
TEST CENTER/REAR
/DELAY
RANDOM OPEN/CLOSE INDEX MODE
VCD/CD TUNER
VIDEO CD CHANGER RECEIVER
VIDEO CD
Version 2.0 / Playback Control
PRESET/TUNING/BAND A/B/C/D/E
OPEN/CLOSE
DISC 1 DISC 2 DISC 3
DISC CHANGE
VOLUME INPUT SELECTOR
VCR•LD/TV•VCD/CD•TAPE/MD•TUNER
VCD/CD TUNER
MIC TONE MIC MIC MIXING
SOFT NORMAL MAX MIN
STANDBY/ON
PHONES
KARAOKE
PROGRAM
ECHO ECHO
MEMORY
MUSIC
DISPLAY MEMORY AUTO/MAN’L REPEAT TIME
TIME ADJ TIMER HOUR MIN
INPUT TRIM
1 6
4
3
2
6
TIME
1
Display information during programming
Playback order
Music calendar Selected disc
Selected track number Total playing time
TRACK
PROGRAM KARAOKE
PRO LOGIC
PROG VOLU
OVER
1 2 3 4
7 8 9 10
13 14 15
5
11
6
12
TRACK
PROGRAM KARAOKE
PRO LOGIC
PROG VOLUM
OVER
1 2 3 4
7 8 9 10
13 14 15
5
11
6
12
Program play
You can program up to 20 tracks in any desired order.
1
Load discs and close the disc table.
2
When in the stop mode, press the PROG button to
prepare for programming.
*
“PROG” and “P-01” will light up on the display, and all
track numbers on the selected disc will begin flashing.
3
If necessary, select a desired disc by pressing the DISC
SKIP button.
*
Just after you change the disc, this unit reads the
contents of the newly selected disc for a few seconds.
During this internal operation, if you go on to the next
step, “WAIT” appears on the display and your
operation is canceled.
4
Use the track number input buttons to select the desired
track number.
*
The selected track number and the total play time of
the programmed tracks will light up on the display, and
soon it will be replaced by the display of the next
playback order. Programmed track numbers on the
selected disc will stop flashing and light up on the
music calendar.
* Pressing the TIME button displays the total play time of
the programmed tracks for about 1 second, and then it
is replaced by the display of the next playback order.
* For example, to choose selection 12
(1) Press the “+10” button.
(2) Within 3 seconds, press the “2” button.
5
Repeat steps 3 and 4 for any other track. Up to 20 tracks
can be programmed.
6
Press the play/pause / button to start playback of
programmed tracks.
Notes
• When this unit is in the Playback Control mode (“PBC” is
illuminated on the display) and the playback is stopped,
pressing the PROG button cancels the Playback Control
mode, and so you can make programming operations.
• It is also possible to program a sequence of tracks while
looking at the list of tracks on the surface of the disc
before closing the disc table.
• During playback or pause, programming is not possible.
• If the total time of the programmed tracks becomes 100
minutes or more, the highest position of the figure will not
be displayed.
• The total time of the programmed tracks will not be
displayed, if track number 16 or higher is programmed.
• Skip search can be performed during playback, but only
within the range of the programmed tracks.
• Manual search can be performed during playback to
search all tracks, including unprogrammed tracks.
•
If programs are made selecting tracks from more than one
disc, pressing the DISC CHANGE button is useless during
program play.
TIME