Utility mode, Creating a program change table, Set the midi receive channel – Yamaha DG130HA User Manual
Page 12: Set the midi merge, Midi bulk out, Midi bulk in, Dg100, Dg80, Dg130h
12
■
Creating a Program Change Table
With this procedure, a specific memory number in the DG amplifier’s internal
memory can be recalled with a program change number received from an
external MIDI device.
* Factory Preset: Program Change Number = Memory Number.
1.
Press and hold the
button for more than one second. The
“UTIL.” mode display lamp will light. (Utility Mode)
2.
Press the
button.
3.
Using the
/
buttons, select the program change number (
1
–
2.8
) that will be sent by the external device. The number will ap-
pear on the display.
4.
Press the
button.
5.
Using the
/
buttons, select the memory number (
1
–
2.8
) to
be recalled from the DG amplifier’s internal memory. The number
will appear on the display.
6.
Depending upon your particular needs, repeat steps 2 through 5 as
needed.
■
Set the MIDI Receive Channel
Set the DG amplifier’s MIDI receive channel.
* To transmit and receive MIDI data between MIDI devices, the MIDI channel on
both devices must be the same or data will not be successfully transferred. (The
factory preset is channel 1.)
1.
Press and hold the
button for more than one second. The
“UTIL.” mode display will light. (Utility Mode)
2.
Press the
button. The currently set MIDI receive channel
will appear on the display.
3.
Use the
/
button to select a MIDI receive channel (
1
–
16
,
All
,
oF
).
* With the “
All
” setting omni is set to on.
■
Set the MIDI Merge
If you want the MIDI signal received by the DG amplifier’s MIDI IN jack to be
transmitted on to other MIDI devices via the DG amplifier’s MIDI OUT jack,
set the MIDI Merge to “
on
” (ON). If you don’t want the data to be transmit-
ted, set to “
oF
” (OFF).
1.
Press and hold the
button for more than one second. The
“UTIL.” mode display will light.
2.
Press the
button. The currently set MIDI merge setting will
appear in the display.
3.
Use the
/
button to select either “
on
” or “
oF
”.
Utility Mode
The Utility Mode is used to perform MIDI settings, set the speaker simulator and volume pedal position settings. To enter the Utility Mode, press
and hold the
button for more than one second, the “UTIL.” mode display lamp will light. Each of the settings will be stored in memory, even
when the power to the amp is turned off. To exit from the Utility Mode, press the
button, the “AMP” (amp mode) display lamp will light.
* MIDI messages cannot be received when in the Utility Mode so, refer to the “Using MIDI to Recall Memory”, “Using MIDI to Control Volume”, “Controlling
Reverb, Tremolo, Chorus and Tape Echo via MIDI” and “MIDI Bulk In” sections in this manual to perform the corresponding MIDI operations.
■
MIDI Bulk Out
You can back up the data stored in the DG amplifier’s internal memory by
saving the data to an external MIDI storage device (Yamaha MDF3, etc.).
1.
With a MIDI cable, connect the DG amplifier’s MIDI OUT jack to the
MIDI IN jack on the external MIDI storage device.
2.
Press the
button for more than one second. The “UTIL.”
mode display lamp will light.
3.
To transmit all memory (128 memory, plus Utility setting data) with
the Bulk Out operation:
→
Press the
button. “
All
” will appear in the display.
To transmit a single memory:
→
Press the
button. Use the
/
button to select the
memory number (
1
–
128
,
All
) that you want to save with the
Bulk Out operation.
* When “
All
” is selected in the Bulk Out operation, all memory data
(128 memory) will be transmitted.
4.
Press the
button to execute the Bulk Out operation. Press
the
button to cancel the operation.
* The device number is the same as that of the MIDI receive channel. If the MIDI
receive channel is set to “All” (Omni ON) the device number will be 1.
■
MIDI Bulk In
With a MIDI cable, connect the DG amplifier’s MIDI IN jack to the MIDI OUT jack
on an external MIDI device. Return your MIDI back up data to the DG amplifier.
* The MIDI Bulk In operation is carried out in the AMP or EFFECT modes only.
It can not be carried out in the Utility Mode.
* The device number is the same as that of the MIDI receive channel. If the MIDI
receive channel is set to “
All
” (Omni On), the MIDI channel will be set to 1.
The DG amplifier will not receive data if the MIDI channel is set to “
oF
”
(OFF).
* “
Ld
” is shown on the display while the MIDI Bulk In operation is being ex-
ecuted.
DG amplifier
Rear Panel
MIDI Cable
External MIDI Device
MIDI IN
MIDI OUT
DG100-
212A
/DG80-
210A
/DG80-
112A
/DG130H
A