Yamaha EM-202VCD - Manual (Page 20)

E-12
SPEAKER BALANCE ADJUSTMENT
SPEAKERS CENTER/REAR VOLTAGE SELECTOR
SPEAKERS FRONT AC OUTLET
MAINS
R L CENTER REAR REAR
REAR SINGLE CENTER :8 Ω MIN./SPEAKER
6 Ω MIN./SPEAKER
SEE OWNER'S MANUAL FOR CONNECTION.
SEE OWNER'S MANUAL FOR CONNECTION.
REAR :4 Ω MIN./SPEAKER REAR SINGLE :8 Ω MIN./SPEAKER
R L
L UNSWITCHED 100W MAX.
AUDIO SIGNAL AUX TAPE•MD LD•TV
AUDIO SIGNAL
VCR SUBWOOFER
R
IN OUT IN OUT
OUT
VCR MONITOR OUT LD•TV
VIDEO SIGNAL
ANTENNA
AM
FM
GND
75 Ω UNBAL.
NORMAL AUTO 50kHz
9kHz 10kHz NTSC
100kHz
FM
AM PHANTOM PAL
CENTER MODE TV MODE FREQUENCY STEP IN OUT
VIDEO SIGNAL
NORMAL
PHANTOM
CENTER
MODE
NORMAL AUTO 50kHz
9kHz
10kHz NTSC
100kHz
FM
AM PHANTOM PAL
CENTER
MODE
TV
MODE
FREQU
PHONES
POWER
DISC 1 2 3
PROGRAM
ECHO ECHO
MUSIC
USER MEMORY
INPUT SELECTOR VCR/LD-TV/VCD-CD/TUNER/TAPE•MD/AUX VOLUME
RANDOM
DISPLAY MIC
MIN MAX
MIC MIXING
REPEAT TIME MEMORY AUTO/MAN'L
HOUR
PRESET/TUNING/BAND A/B/C/D/E
MIN TIME ADJ TIMER
OPEN/
CLOSE
DISC
CHANGE
VIDEO CD
Version 2.0 / Playback Control
TIME
A
PROG
B C D
+ I0
E
VCD/CD
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9 0
PRESET
INPUT
TIME INDEX
INTRO DIGEST
POWER
DISPLAY SLEEP
MUSIC
FLAT
PROGRAM USER
VOLUME
DISC SKIP RETURN PREV NEXT SELECT
LEVEL
TEST CENTER/REAR
/DELAY ECHO/
KEY
OPEN/CLOSE INDEX MODE TUNER
This procedure lets you adjust the sound output level balance
between the front, center, and rear speakers using the built-in
test tone generator. When this adjustment is performed, the
sound output level heard at the listening position will be the
same from each speaker. This is important for the best
performance of the built-in Dolby Pro Logic surround decoder.
The adjustment of each speaker output level should be
done at your listening position with the remote control
transmitter. Otherwise, the result may not be satisfactory.
Before operation
Set the CENTER MODE switch on the rear panel of this unit
to the position suitable for your speaker system configuration.
(Refer to page 7 for details.)
NORMAL (For 5 speaker configuration):
Select this position when you use the center speaker.
PHANTOM (For 4 speaker configuration):
Select this position when you do not use the center
speaker. The center sound will be output from the left
and right front speakers.
1
Press the POWER switch to turn the power on.
2
Turn the VOLUME control fully counterclockwise to
decrease the volume to minimum.
3
Press the PROGRAM button once or more so that “
PRO LOGIC” lights up on the sound field program
indicator.
4
Press the TEST button.
* “TEST” flashes on and off on the display.
5
Press the VOLUME + (up) button to increase the volume.
You will hear a test tone (like pink noise) from the left front
speaker, then the center speaker, then the right front
speaker, and then the rear speakers, for about two seconds
each. The display changes as shown below.
* The test tone from the left rear speaker and the right rear
speaker will be heard at the same time.
(L and R) 4
3
1
5
2
3 1
2, 5