Waterford Appliances T25-LP - Manual (Page 6)

6 Waterford TARA T25 Direct Vent Freestanding Gas Stove
specified vent and termination cap to the
outside of the building envelope. Never vent
to another room or inside a building. Make
sure that the vent is fitted as per the instruc-
tions starting on page 9.
6) Inspect the venting system annually for
blockage and any signs of deterioration.
7) Venting terminals shall not be recessed into
a wall or siding.
8) Any safety glass removed for servicing
must be replaced prior to operating the
appliance.
9) To prevent injury, do not allow anyone who
is unfamiliar with the operation to use the
fireplace.
INSTALLATION
CHECKLIST
1) Check Clearances to Combustibles (page
6), location of unit (page 7) and venting
requirements (pages 9-20).
2) a) Carefully unpack the unit from the pack-
aging.
EXTREME CARE NEEDS TO BE
TAKEN WHEN HANDLING POR-
CELAIN ENAMEL PARTS OR
CERAMIC LOGS TO AVOID
DAMAGE. DAMAGE TO THESE
PARTS IS NOT COVERED UN-
DER WARRANTY.
b) Use a 7/16" wrench to remove the two
lag bolts used to secure the stove to the
pallet.
c) Locate the 4 leg levelling bolts supplied
with the stove. Fit these bolts to the
underside of the legs as shown. These
levelling bolts can be used to level the
stove on an uneven surface.
Thermostat. Some areas may have further
requirements, check local codes before
installation.
5) This appliance is Listed for Alcove installa-
tions, maintain minimum Alcove clearances
as follows, minimum width of 33-1/2"
(851mm), a maximum depth of 24" (610mm),
and minimum ceiling height of 41-1/2"
(1054mm).
6) We recommend that you plan your installa-
tion on paper using exact measurements
for clearances and floor protection before
actually installing this appliance. Have a
qualified building inspector review your
plans before installation.
MANUFACTURED
MOBILE HOME
ADDITIONAL
REQUIREMENTS
1) Ensure that structural members are not cut
or weakened during installation.
2) Ensure proper grounding using the #8
ground lug provided.
3) Appliance must be anchored to the floor
with the supplied anchoring methods.
GENERAL SAFETY
INFORMATION
1) The appliance installation must conform
with local Canadian Electrical Code.
2) The appliance when installed, must be elec-
trically grounded in accordance with local
codes, or in the absence of local codes with
the current National Electrical Code, ANSI/
NFPA 70 or CSA C22.1 Canadian Electrical
Code.
3) The appliance should be inspected for
shipping damage before use and serviced
annually by a professional service per-
son. More frequent cleaning may be re-
quired due to excessive lint from carpeting,
bedding material, etc. It is imperative that
control compartments, and circulating air
passageways of the appliance be kept
clean and free from excessive lint from
carpeting.
4) See general construction and assembly
instructions. The appliance and vent should
be enclosed when installed in or passing
through a living area, where children may
come in contact with it.
5) This appliance must be connected to the
INSTALLATION
3) Install Optional Fan, see page 7.
4) Install venting: Check all venting require-
ments, pages 9 to 20. Minimum Horizontal
Vent Kit, page 11, Vertical Termination Co-
Linear Flex System, page 13, DV Stove
Horizontal Vent Kit (page 14), and the Dura-
Vent Termination Kits, page 15. Converting
a Class-A Metal Chimney or Masonry Chim-
ney to a Direct Vent System, page 21.
5) Make gas connections, page 24. Test the
pilot. Must be as per diagram, page 26.
6) Test Gas Pressure, page 24.
7) Install logs where indicated on page 27.
8) Install Optional Side Shelves, page 27.
9) Install optional Remote Control, or Wall Ther-
mostat, pages 27 and 28.
10) Final check, page 28.
Before leaving this unit with the customer, the
installer must ensure that the appliance is firing
correctly and operation fully explained to
customer.
This includes:
1) Clocking the appliance to ensure the cor-
rect firing rate (rate noted on label), first
burning the appliance for 15 minutes.
2) If required, adjusting the primary air to
ensure that the flame does not carbon. First
allow the unit to burn for 15-20 min. to
stabilize.
CAUTION: Any alteration to the product
that causes sooting or carboning that
results in damage is not the responsibil-
ity of the manufacturer and is not a war-
ranty issue.
CLEARANCES TO
COMBUSTIBLES
The clearances listed are MINIMUM distances.
Measure the clearance to both the appliance
and the chimney connector. The farthest
distance is correct if the two clearances
do not coincide.
For example, if the appliance is set as indicated
in one of the figures but the connector is too
close, move the stove until the correct clear-
ance to the connector is obtained.
This appliance may be installed only with the
clearances as shown in the situations pic-
tured. Do not combine clearances from
one type of installation with another in
order to achieve closer clearances.
This unit can be installed on a solid combustible
surface like a wood floor. This unit can also be
installed directly on carpeting or vinyl.
Emissions from burning wood or gas could
contain chemicals known to the State of
California to cause cancer, birth defects or
other reproductive harm.