Sylvania DVR90DG - Manual (Page 31)

31
Checking, canceling, or correcting the timer programming
information
7
Press [ENTER] when
information is entered. Your
program setting will be stored.
• To set another program, repeat
steps 2 to 7.
• To exit, press [TIMER PROG.]
or [SETUP].
• When two or more programs are
overlapped, “Overlap” and the
overlapped program number will
appear in the display.
8
Press [POWER] to turn off.
Recording
Recording
Playing
discs
Editing
Before
you
start
Connections
Getting
started
Changing
the
Setup
menu
Others
Español
POWER
ZOOM
DISPLAY SETUP
T OP MENU MENU/LIST
REC SPEED
REC/OTR
PAUSE SKIP SKIP
PL AY
CM SKIP
REPEAT
OPEN/CLOSE
TIMER
PROG.
FWD REV
CLEAR
1 2 3
4 5 6
7 8 9
SPACE
0
A
H G
ENTER
CH
RETURN
.@/: ABC DEF
GHI JKL MNO
PQRS TUV WXYZ
B
C
{ B
K
L
h g
F
STOP
B x1.3/0.8
8
1
Press [POWER].
2
Press [TIMER PROG.].
Timer Programming list will appear.
3
Check the information on the
list you will need.
4
To clear the timer programming:
Using [K / L], select your
desired program. Press
[CLEAR].
To correct the timer program-
ming:
Using [K / L], select your desired
program. Press [ENTER].
Next, correct the timer programming
by using
[K / L / { / B].
Finally, Press [ENTER] again.
5
Press [TIMER PROG.] to exit.
6
Press [POWER] to return to the
timer standby mode.
Note
• Press [TIMER PROG.] to
check the timer programming
in process.
When the Timer Recording is
proceeding, that program will
be highlighted in red.
7
POWER
ZOOM
DISPLAY SETUP
T OP MENU MENU/LIST
REC SPEED
REC/OTR
PAUSE SKIP SKIP
PL AY
CM SKIP
REPEAT
OPEN/CLOSE
TIMER
PROG.
FWD REV
CLEAR
1 2 3
4 5 6
7 8 9
SPACE
0
A
H G
ENTER
CH
RETURN
.@/: ABC DEF
GHI JKL MNO
PQRS TUV WXYZ
B
C
{ B
K
L
h g
F
STOP
B x1.3/0.8
2
5
6
4
1
Press [CLEAR] to erase the
selected program.
Each error number means:
Timer Programming
2. ---
3. ---
4. ---
5. ---
6. ---
7. ---
8. ---
1. JAN/01 12:57AM 1:57AM CH8 1H
Date Start End CH Speed
To stop the Timer Recording in process
Press [STOP C] on the front panel of the unit.
[STOP C] on the remote control is not effective.
If the timer program did not complete correctly, the error number
appears in the Timer Programming list.
Timer Programming
2. ---
3. ---
4. ---
5. ---
6. ---
7. ---
8. ---
* JAN/01 12:57AM 1:57AM CH8 E22
Date Start End CH Speed
• A program with the error number is grayed and asterisked in the Timer Programming list.
• Once the Timer Programming list with error line(s) is displayed, or after canceling and setting again the timer
standby mode, the program line(s) with error will be cleared.
indicator will appear on the
front panel display.
indicator disappears from the
front panel display.
Timer Recording (cont’d)
E1-22
E37-39
Recording error other than
below
E35 PCA full
E36 Already finalized Video
format disc E23-24 Unrecordable disc
E25-28 Copy prohibited program E40 Some portion has not
been recorded because
of program overlapping.
Recording did not start at
the start time.
E29 Disc protected
E30 Disc full
E31-32 Already 99 titles recorded
E33 Already 999 chapters
recorded
E41 Power failed
E34 No space for Control
information
E42 No disc when recording