Advanced setup —continued – Onkyo 29344934 User Manual
Page 71
71
SurrBack
*3*4
Small: Select if the surround back speakers are small (default).
Large: Select if the surround back speakers are large.
None: Select if no surround back speakers are connected.
SurrBack Ch
*5
2ch: Select if two (left and right) surround back speakers are connected.
1ch: Select if only one surround back L speaker is connected.
*3 If the “Surround” setting is set to “None”, this setting does not appear.
*4 If the “Surround” setting is set to “Small”, the Large option cannot be selected.
*5 If the “Surround” or “SurrBack” settings are set to “None”, this setting does not appear.
Crossover (Crossover Frequency)
This setting is set automatically by the Audyssey 2EQ™ Room Correction and Speaker Setup function
(see page 39).
This setting only applies to the speakers that you specified as “Small” in the “3. Sp Config” on page 70.
To get the best bass performance from your speaker system, you need to set the crossover frequency according
to the size and frequency response of your speakers.
Use the diameter of the smallest speaker in your system when choosing the crossover frequency.
Speaker cone diameter
Crossover frequency
Over 8 in. (20 cm)
40/50/60Hz*
6-1/2 to 8 in. (16–20 cm)
80Hz
5-1/4 to 6-1/2 in. (13–16 cm)
100Hz (default)
3-1/2 to 5-1/4 in. (9–13 cm)
120Hz
Under 3-1/2 in. (9 cm)
150 /200Hz*
*
Choose the setting suitable for the speaker.
Notes:
• For a more accurate setting, look up the frequency response in the manuals supplied with your speakers and
set accordingly.
• Choose a higher crossover frequency if you want more sound from your subwoofer.
Double Bass
This setting is not set automatically by the Audyssey 2EQ Room Correction and Speaker Setup function
(see page 39).
With the Double Bass function, you can boost bass output by feeding bass sounds from the front left, right, and
center to the subwoofer. This function can be set only if the “Subwoofer” setting is set to “Yes”, and the “Front”
setting is set to “Large” in the “3. Sp Config” on page 70.
On: Double Bass function on. Bass from the front left and right channels is also fed to the
subwoofer (default).
Off: Double Bass function off.
4. Sp Distance (Speaker Distance)
These settings are set automatically by the Audyssey 2EQ Room Correction and Speaker Setup function (see page 39).
With these settings, you can specify the distance from each speaker to the listening position.
Measure and make a note of the distance from each speaker to the listening position.
Notes:
• Speakers that you set to “No” or “None” in the “3. Sp Config” (page 70) cannot be selected.
• These settings cannot be changed while a pair of headphones is connected, or speaker set A is off, or speaker set B
is on, or the AV receiver is muted.
• The Center and Subwoofer distances can be set up to 5 ft. (1.5 m) more or less than the Left distance. For example,
if the Left distance is set to 20 ft. (6 m), the Center and Subwoofer distances can be set between 15 and 25 ft. (4.5
and 7.5 m).
• The Surround distances can be set up to 5 ft. (1.5 m) more or 15 ft. (4.5 m) less than the Left distance. For example,
if the Left distance is set to 20 ft. (6 m), the SurrRight and SurrLeft distances can be set between 5 and 25 ft. (1.5
and 7.5 m).
HT-S5200_En.book 71 ページ 2009年3月9日 月曜日 午後4時31分