Ricoh Aficio CL3000 User Manual

Page 4

○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○

○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○

○○○○○○○○○○

○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○

Printed in The Netherlands

EE GB

○○○○○○○○○○○○○○○○○○○○○○○○○○○

○○○○○○○○○○○○○○○○○○○○○

○○○○○○○○○○○○○○○○○

○○○○○○○○○○○○○○○○○○○○○○○○○○○○○

○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○

○○○○○○○○○○○○○○○

○○○○○○○○○○○○○○○○○○○○

○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○

CONFIGURING THE PRINTER
FOR THE NETWORK

You must configure the printer setting using the
control panel when using in a network environment.
The following list is the items you can set and their
default settings.

DHCP

IP Address

011.022.033.044

Subnet Mask

000.000.000.000

Gateway Address

000.000.000.000

Frame Type (NW)

Auto

Active Protocol

TCP/IP

Ethernet

Auto

The procedure below shows how to set the TCP/IP
protocol. Make the settings for the other items by
taking the same procedure.

Press the

{

Menu

}

key.

“Menu” appears on the panel display.

Menu:

Paper Input

Press the

{▲}

{▼}

key to display “Host

Interface”, and then press the

{

Enter #

}

key.

Menu:

Host Interface

The interface setiing menu appears.

Start the protocol for use.

Press the

{▲}

{▼}

key to display

“Network Setup”, and then press the

{

Enter

}

key.

Host Interface:

Network Setup

Press the

{▲}

{▼}

key to display “Active

Protocol”, and then press the

{

Enter #

}

key.

Network Setup:

Active Protocol

Press the

{▲}

{▼}

key to display “TCP/

IP”, and then press the

{

Enter #

}

key.

Active Protocol:

TCP/IP

Press the

{▲}

{▼}

key to display “Active”,

and then press the

{

Enter #

}

key.

TCP/IP:

*Active

Note

❒ * shows the current setting.

In about two seconds, the display returns to the “Active Protocol”
setting screen.

Set the rest of the protocols for use.

When all settings for the protocol are done,

press the

{

Escape

}

key.

The “Network Setup” setting screen appears.

Note

❒ The default settings for all of the protocols are

“Active”.

❒ It is recomended to set the unused protocols “Not

Active”.

When you use this machine under DHCP
environment, go to step . When you use this
machine with a fixed IP address, you must make
the setting for the required item after making the
setting for DHCP Off. Go to step .

Important

❒ When DHCP is On, you cannot make the setting for

the following menus:

IP Address
Subnet Mask
Gateway Address

Note

❒ Consult the network administrator for information

about how to make the setting for the network

Make the setting for DHCP Off.

Press

{▲}

{▼}

to display “DHCP”, and

then press

{

Enter #

}

Network Setup:

DHCP

Press

{▲}

{▼}

to display “Off”, and then

press

{

Enter #

}

DHCP:

*Off

Note

❒ * shows the current setting.

In about two seconds, the display returns to the “Network Setup”
setting screen.

Set the IP address for the printer.

Note

❒ Confirm the IP address to the network administrator.

Press the

{▲}

{▼}

key to display “IP

Address”, and then press the

{

Enter #

}

key.

Network Setup:

IP Address

The currently selected IP address appears.

Note

❒ When the {Enter #} key is pressed, the cursor moves

to the next field.

❒ When the {▲} or {▼} key is kept pressed for a few

seconds, the value chages by 10.

Press the

{▲}

{▼}

key to set the value

for the field.

IP Address:

199.022.033.044

Press the

{

Enter #

}

key.

The cursor moves to the next field.

Repeat

and

to set the value for the rest

of the fields.

Set “Subnet Mask” and “Gateway Address” by
following the same procedure for setting the IP
address.

Important

❒ The subnet mask is the mask value to use a part of

the IP address as a network address. Confirm the
value to the network administrator.

❒ The gateway address is the address of the host or

router that acts as a gateway when interacting with
work stations in another network. Confirm the value
to the network administrator.

Note

❒ If you are not sure of the setting addresses, leave

them as default.

When all of the settings are done, press the

{

On Line

}

key.

“Ready” appears on the panel display.

Ready

Print the configuration page to confirm the settings
made.

See “PRINTING THE TEST PAGE” for printing the configuration

page.

INSTALLING THE PRINTER
DRIVER

You can install the printer drivers and software
easily from the CD-ROM labeled “Printer Drivers
and Utilities”.
The supported operating systems are Windows 95/
98/Me, Windows 2000, Windows XP and Windows
NT 4.0.
Click [Quick Install] in the window of the CD-ROM
to install PCL5c and RPCS printer drivers. To install
the PostScript 3 printer driver, click the [PostScript
3 printer driver] button. For more information about
the PostScript 3 printer driver, see the Administrator
Reference or the Client Reference on the CD-ROM
labeled “Operating Instructions” depending on the
environment you use in.
When the TCP/IP protocol is used, SmartNet-
Monitor for Client will be installed as well.

When using with TCP/IP protocol, confirm the followings:

❒

The printer is connected to a network with
the network interface cable.

❒

The TCP/IP protocol is set.

❒

The IP address is set for the printer and the
computer.

Insert the CD-ROM labeled “Printer Drivers and
Utilities” into the CD-ROM drive.

Auto Run will start the installer.

Select a language to change the interface
language, and then click [OK].

The following languages are available:

Cestina (Czech), Dansk (Danish), Deutsch (German), English
(English), Espanol (Spanish), Francais (French), Italiano (Italian),
Magyar (Hungarian), Nederlands (Dutch), Norsk (Norwegian),
Polski (Polish), Portugues (Portuguese), Suomi (Finnish), Svenska
(Swedish)

Default interface language is English.

Select [Quick Install].

The software license agreement appears in the [License Agreement]
dialog box.

This is an example when English is selected in step .

After reading through all of the contents, click [I

accept the agreement] to agree with the License
Agreement, and then click [Next].

Select the printer model you want to install in the
“Select Printer” dialog box.

Note

❒ For a network connection with TCP/IP, select the

printer whose IP address is displayed in [Connect
to].

❒ For parallel connection, select the printer whose

printer port is displayed in [Connect to].

Click [Install].

The following display appears while installing the printer driver.

When finished, the [Installation Completion] dialog box appears.

Note

❒ Under Windows 2000, the [Digital Signature Not

Found] dialog box may appear when installing the
printer driver. In this case, click [Yes] to continue
the installation.

❒ Under Windows XP, the [Hardware Installation]

dialog box may appear. In this case, click [Continue
Anyway] to continue the installation.

Click [Finish].

Note

❒ A message directing to restart the computer may

appear. In this case, restart your computer to
complete the installation. If no a message appears,
go to step

Click [Exit].

The installation is now complete.