NuTone LA-204WH - Manual

TO REGISTER THIS PRODUCT, VISIT WWW.NUTONE.COM
INSTALLATION & OPERATING INSTRUCTIONS
READ & SAVE THESE INSTRUCTIONS!
Plug-in Door Chime Receiver
with Strobe Light
MODEL: LA-204WH
For use with NuTone LA-206TWH
and LA-207TWH Pushbutton
FIGURE 3
COVER
FIGURE 4
TO INSTALL:
1. Simply plug chime receiver into any
standard electrical wall outlet within
100 feet (30 meters) of pushbutton.
(Chime is powered by household current.)
2. Chime will sound and strobe will flash
when pushbutton is pressed.
Note: Chime receiver will not work alone.
MOUNTING THE PUSHBUTTON
Refer to Figures 1 and 2.
1. Locate the pushbutton next to or near the door. Do not mount the
wireless pushbutton on a metal surface. Caution: Some stucco
houses have metal mesh in the wall structure which will affect
the wireless chime performance. Experiment with various
positions of receiver with respect to the pushbutton to
determine the location that gives best performance before
mounting permanently. If not satisfied, use a wired chime.
2. Remove the pushbutton cover by inserting the tip of a screwdriver in
the slot at the bottom of the pushbutton and then gently rock the
pushbutton cover apart from the pushbutton base.
3. Choose a level place to locate the pushbutton base.
4. Position the pushbutton base, and mark the mounting surface with a
pencil through the two holes in the pushbutton.
5. Drill two 3 ⁄
16
" diameter holes at the previously marked area.
6. Insert the plastic anchors into the 3 ⁄
16
" diameter holes.
7. Place pushbutton base over anchors, and fasten with two screws
provided.
Do not replace cover at this time.
8. Apply a small amount of caulking to the mounting screw holes on the
base for waterproofing.
SLOT
DO NOT MOUNT ON
METAL SURFACE
LIP
MOUNTING
SCREWS
WATERPROOF
GASKET
BASE
WOODEN WALL OR
DOOR FRAME
PLASTIC
WALL
ANCHORS
TOP
P.C. BOARD
BATTERY
LOCATION
SECURITY
CODE
SETTING
FIGURE 1
TO OPEN
COVER “PUSH”
SLOT
FIGURE 2
SLOT
TO OPEN
COVER “PUSH”
Congratulations on your purchase of a NuTone wireless chime. The chime
operates by radio frequency signal transmitted by the pushbutton and
received by the chime. The pushbutton/transmitter is mounted at the door.
The receiver may be located anywhere in your home within 100 feet
(30 meters) of the pushbutton. The pushbutton/transmitter can be
programmed to sound one of three chime sounds. This feature allows up
to three pushbuttons to generate three different chime sounds.
No electri
cal wiring
needed!
PROBLEM
1. Chime does not sound. • Check position of battery (+/-) in
pushbutton.
• Make sure pushbutton is not located
on a metal surface.
• Check that outlet on chime receiver
has power
• Check pushbutton and chime codes.
These codes must match.
2. Chime is activated by another wireless
device.
Change the security code in the
pushbutton and chime receiver.
These codes must match.
(See detailed instructions below.)
SOLUTION
PUSHBUTTON SECURITY CODING
Refer to Figure 3.
It is not necessary to change the security code of the pushbutton
unless you experience interference from other wireless devices.
1. To change the security code, remove any combination of the six
plastic jumper straps.
2. NOTE: Both the pushbutton and receiver codes must match.
BATTERY INSTALLATION
Refer to Figure 3.
1. Position the A23 12 volt battery as illustrated.
Be sure to observe
polarity (+/–). For replacement battery, use EverReady ® A23BP or
Duracell ® MN21B (or equivalent).
INSTALLING PUSHBUTTON COVER
1. Position the pushbutton cover over the pushbutton base so that the
“lip” on the base engages into the “slot” on the cover. Make sure the
rubber gasket is properly seated. Firmly press cover until it snap fits
over the base.
IF YOU SHOULD ENCOUNTER A PROBLEM: