Messages – Parrot DMP-BD80 User Manual
Page 36
36
RQT9401
Messages
The following messages or service numbers appear on the television or unit’s display when something unusual is detected during startup and
use.
On the television
Page
Authorisation Error.
This unit is not authorised to
play this title.
≥[DivX] You are trying to play the DivX VOD content that was purchased with a different
registration code. You cannot play the content on this unit.
Cannot play.
≥You inserted an incompatible disc.
6, 7
Cannot play on this unit.
≥You tried to play a non-compatible image.
≥Confirm “SD” on the unit’s display is not blinking and re-insert the card.
—
No disc is inserted.
≥The disc may be upside down.
—
Rental Expired.
≥[DivX] The DivX VOD content has zero remaining plays. You cannot play it.
$ This operation is not
available.
≥Some operations are unsupported by the unit. For example;
– [BD-V]
:
During play back, reverse slow-motion or reverse frame-by-frame is not possible.
$ This operation is prohibited
by this disc.
≥Depending on the disc, you may not be able to perform search or skip when film previews
and warning screens are being played back.
Cannot connect.
Please check the connection of
the LAN cable.
≥When a hub is used but its Link lamp does not light up, check the cable connection, LAN
terminal connection, cable itself (a cross cable may be used by mistake), etc.
13
IP address is not set.
≥The “IP Address” in “IP Address / DNS Settings” is “---. ---. ---. ---“. Set the “IP Address”,
“Subnet Mask”, and “Gateway Address“. (Select the automatic address acquisition if
necessary.)
Cannot obtain IP address.
Please check the connection or
setting of the router.
≥If you use a hub, then check the connection between the hub and the router.
– Use the UPLINK port of the hub to connect to a router.
– Check whether or not the hub’s Link lamp lights up. If it does not light up, then check the
cable connection, LAN terminal connection, cable itself (a cross cable may be used by
mistake), etc.
≥If the above conditions are OK, then the router may not operate in DHCP mode. Check the
router settings and operation. You may reset the router to restore it to normal.
13
13
This IP address is already in
use.
Please check the setting.
≥This unit’s IP address is used by another device. Check the IP addresses of this unit,
personal computers, and routers, etc. If necessary, reconfigure them to avoid IP
addresses from being duplicated.
—
Connection test could not be
conducted.
≥Turn the unit off. Remove the AC mains lead and reconnect it and try again. If the same
symptom persists, then consult your dealer.
—
IP address is not set correctly.
Connection test was
unsuccessful. No reply from
Gateway. Please check the
connection or setting of the
router.
≥If you use a hub, then check the connection between the hub and the router.
– Use the UPLINK port of the hub to connect to a router.
– If the hub’s Link lamp does not light up, then check the cable connection, LAN terminal
connection, cable itself (a cross cable may be used by mistake), etc.
≥Check the “IP Address”, “Subnet Mask”, and “Gateway Address” in the “IP Address / DNS
Settings”.
≥If the MAC address information is required, then press [SETUP] to display the “Network
Settings” menu.
13
Network connection was
rejected.
Please confirm Setup “BD-Live
Internet Access”.
≥When you set “BD-Live Internet Access” to “Limit” and play BD-Live contents which do not
have a content owner certificate, the Internet access of the content is not allowed. If you
allow the content to connect to Internet, set “BD-Live Internet Access” to “Permit”.
Could not check for latest
firmware version.
Please try again later.
≥The firmware download server is currently unavailable. Please try again later.
—
High Clarity Sound is effective.
Analog video output is turned
off when playback starts.
≥[BD80] “High Clarity Sound” in setup menu is set to “Enable”, and “High Clarity Sound” in
on-screen menu is set to “On”.
DMP-BD80&60EB&EG&EF&GN-RQT9401_eng.book 36 ページ ２００９年２月６日 金曜日 午後５時２２分