Polk Audio RMDS-1 User Manual
Page 30
Polk customer service (800) 377-7655
30
RMDS-1 Specifications
System
Overall Frequency Response
30Hz—24kHz
-3dB Frequency Response Limits
38Hz—20kHz
Subwoofer to Satellite/Center Crossover Design
Active 4th order (24dB/octave) low-pass and high-pass,
150Hz acoustic crossover.
Maximum Sound Pressure Level
105 dB in an IEC Standard 80 cubic meter
(2825 cubic foot, e.g. 15'W x 22'L x 8
1
⁄
2
'H) room
Satellites
Driver Complement:
1-3
1
⁄
4
" magnetically shielded midrange driver with polypropylene cone
and butyl rubber surround
1-
3
⁄
4
" silk dome tweeter w/neodymium magnet (self shielded)
Crossover Design:
2nd order (12dB per octave slopes, electrical) symmetrical topology;
mid-tweeter crossover @ 3.1 kHz; Mylar film capacitors in tweeter’s
signal path.
Dimensions:
4"W x 6
3
⁄
4
"H x 5"D
Center Channel
Driver Complement:
2-3
1
⁄
4
" magnetically shielded drivers with polypropylene cones and
butyl rubber surrounds
1-
3
⁄
4
" silk dome tweeter w/neodymium magnet (self shielded)
Crossover design:
2nd order (12dB per octave slopes, electrical) symmetrical topology;
mid-tweeter crossover @ 2.5 kHz; Mylar film capacitors in tweeter’s
signal path.
Dimensions:
11
1
⁄
2
"W x 4
1
⁄
2
"H x 5
3
⁄
4
"D
Subwoofer
Driver Complement:
1-10" magnetically shielded driver with 1
1
⁄
2
" voice coil, polypropylene
cone and butyl rubber surround
Crossover design:
Fixed, active 4th order (24dB/octave) low-pass with amplitude shaping
Cabinet Dimensions:
15
1
⁄
2
"W x 18
3
⁄
4
"H x 19
1
⁄
2
"D
Six Channel Power Amplifier
System Continuous Power Output
Greater than 500 Watts into 4 Ohms,
all channels driven*
Dynamic Power Output:
700 watts into 4 Ohms, all channels driven*
Bandwidth
20Hz-22kHz
Distortion
0.05%
Power Requirement
AC 120V, 50/60Hz
Maximum Power Consumption
800 Watts
Preamp/Processor
FM Tuner Section
Usable Sensitivity
IHF 1.3 eV/13.5dBf
Signal to noise ratio
Mono/Stereo 76/68dB
Distortion
Mono/Stereo 0.2/0.5%
Stereo Separation
1 kHz 40dB
Alternate Channel Selectivity
± 400kHz 65dB
Image Rejection
98 MHz 50dB
AM Tuner Section
Usable Sensitivity:
Loop 500µV
Signal to noise ratio
50dB
Selectivity
± 20kHz 70dB
Image Rejection
98 MHz 50dB
General
Power Requirement
AC 120V 60Hz
Power Consumption (AC-3 RF)
26W
Dimensions (Max)
17
1
⁄
4
"W x 4
1
⁄
2
"H x 14"D
*Power ratings alone cannot predict actual sound output. Loudspeaker
efficiency is by far the most important factor in determining how loud your
system will play. For this reason we also specify the calculated maximum
sound output of the RMDS-1 system in a 2825 cu ft. room (for example,
one measuring approximately 15'W x 22'L x 8
1
⁄
2
'H). The maximum SPL
(volume) of the RMDS-1 in such a room would be 105 dB, as loud as
a rock band at 150 feet; certainly loud enough to get you evicted from
a New York City apartment. There are worse fates.