Philips FW P88 - Manual (Page 20)

20
English
3139 116 19721
STANDBY ON
MINI HIFI SYSTEM
BAND C 1 • 2 • 3 CDR
DUB (HSD) RECORD A. REV DIM CLOCK/
TIMER PROG
BASS TREBLE
wOOx TECHNOLOGY
POWER SAVE
IR SENSOR
VOLUME
PLUS LEVEL
STOP•CLEAR SEARCH• TUNING PLAY PAUSE PREV NEXT SIDE PRESET ▲ ▲ BASS/ TR EB LE
P E R S O N A L
D S C
VE C
TAPE 1•2 CD 1•2•3 CDR/DVD
TAPE CD TUNER AUX
LEFT CENTER RIGHT
SURR SURR
PRO LOGIC RDS
DOLBY B NR
NEWS/TA
CD TEXT BAND
Note:
– For 'EASY SET' feature, please refer to
page 13.
Tuning to radio stations
1 Press TUNER (BAND) to select TUNER
mode.
™ "TUNER" will be displayed.
A few seconds later, the current radio
frequency will be displayed.
2 Press TUNER (BAND) again to select
the desired waveband : FM, MW or LW.
3 Press à or á for more than one
second, then release.
™ The display will show "SEARCH"
until a radio station with sufficient
signal strength is found.
• Repeat this procedure until the desired
station is reached.
• To tune to a weak station, briefly press
à or á repeatedly until the display
shows the desired frequency and/or
when the best reception has been
obtained.
Storing Preset Stations
You can store up to 40 radio stations in the
memory. When a preset radio station is
selected, the preset number appears next
to the frequency on the display.
Automatic programming
1 Press TUNER (BAND).
2 Press PROG for more than one second.
™ The PROGRAM starts flashing and
" AUTO" will be displayed.
TUNER
™ The system will start searching for all
radio stations with RDS and then
followed by radio stations on FM,
MW and LW band respectively.
™ All available stations will be stored
automatically. The frequency and
preset number will be displayed
briefly.
™ The system will stop searching when
all the available radio stations are
stored or when the memory for 40
preset radio stations is used.
™ The system will remain tuned to the
last stored preset radio station.
Notes:
– You can cancel the automatic
programming by pressing PROG orÇ
(on the system only).
– If you want to reserve a section of
preset numbers, for example preset
numbers 1 to 9, select preset 10 before
starting automatic programming, only
the preset numbers 10 to 40 will be
programmed.
Manual programming
1 Press TUNER (BAND).
2 Press TUNER (BAND) again to select
the desired waveband : FM, MW or LW.
3 Press PROG for less than one second.
™ The PROGRAM starts flashing.
™ The next available preset number will
be displayed for selection.
4 Press à or á to tune to the desired
frequency.
• If you wish to store the radio station to
another preset number, press 4 or 3
(or Digit 0-9 on the remote control) to
select the desired preset number.
5 Press PROG again.
™ The PROGRAM disappears and the
radio station will be stored.
• Repeat steps 3 – 5 to store other preset
radio stations.
Notes:
– When 40 radio stations are stored and
you attempt to store another radio
station, the display will show
"
PROGRAM FULL”. If you want to
change an existing preset number,
repeat steps 3 – 5.
– You can cancel manual programming by
pressing Ç (on the system only).
– During programming, if no button is
pressed within 20 seconds, the system
will exit program mode automatically.
Tuning to Preset Radio
Stations
• Press 4 or 3 (or Digit 0-9 on the
remote control) to select the desired
preset number.
™ The preset number, radio frequency,
and waveband appear on the display.
pg 01-31/P88/22-Eng 3/6/00, 1:27 PM 20