Panasonic DMR-XW350 - Manual (Page 95)

95
RQT9429
Ref
erence
Additional connections
Connecting a television with S VIDEO
terminals
The S VIDEO OUT terminal achieves a more vivid picture than the
VIDEO OUT terminal. (Actual results depend on the television.)
Connect to terminals of the same colour.
Supplied Audio/Video cable can also be used as an alternative for
Audio cable without connecting the video connector (yellow).
This unit’s rear panel
S Video
cable
Audio cable
Television’s rear panel
OUTO UT
N
P R P B Y
ONENT
O OUT
DIGITAL
AUDIO OUT
(PCM/ BITSTREAM)
S VIDEO
IN
AUDIO I N
R L
V IDEO
I N
Connecting a television with
COMPONENT VIDEO terminals
OPTICAL
COAXIAL
OUTO UT
A V4 IN A V4
IN
S VIDEO VIDEO R-AUDIO-L
P R P B Y
10BASE-T/
100BASE-TX
COMPONENT
VIDEO OUT
DIGITAL AUDIO OUT
(PCM/ BITSTREAM)
R- L
AUDIO IN
R L
P R P B Y
COMPONENT
VIDEO IN
Television’s rear panel
This unit’s rear
panel
Component
video cable
Audio cable
COMPONENT VIDEO terminals can be used for either interlace or
progressive output ( ➡ 114) and provide a purer picture than the S
VIDEO OUT terminal.
Connect to terminals of the same colour.
Supplied Audio/Video cable can also be used as an alternative for
Audio cable without connecting the video connector (yellow).
Required setting
“Component Resolution” setting in the Setup menu ( ➡ 89)
If you have a regular television (CRT: cathode ray tube)
Progressive output may cause some fl ickering, even if it is
progressive compatible. Set “Component Resolution” in the Setup
menu to “576i/480i” and “HDMI Video Mode” to “Off” if you are
concerned about it ( ➡ 89). This is the same for multi system
televisions using PAL mode.
Progressive output
DO NOT
CRT
COMPONENT
VIDEO OUT
This unit
COMPONENT
VIDEO IN
Connecting a stereo amplifi er
Connect to terminals of the same colour.
Supplied Audio/Video cable can also be used as an alternative for
Audio cable without connecting the video connector (yellow).
AUDIO I N
R L
OUTO UT
A V4 IN A V4
IN
S VIDEO VIDEO R-AUDIO-L
P R P B Y
COMPONENT VIDEO OUT
DIGITAL AUDIO OUT
(PCM/ BITSTREAM)
Amplifi er’s rear panel
Audio cable
This unit’s rear panel
Connecting an amplifi er with a digital
input terminal
Required setting
“Digital Audio Output” in the Setup menu ( ➡ 87)
When this unit is connected to an amplifi er with an optical digital
audio cable or coaxial cable and connected to a television with an
HDMI cable, you can enjoy the highest quality of audio from the
disc by setting “HDMI Audio Output” to “Off” in the Setup menu
( ➡ 89). In this case audio is only output from the amplifi er not the
television.
Before purchasing an optical digital audio cable (not included),
check the terminal shape of the connected equipment.
■ With OPTICAL
You cannot use DTS Digital Surround decoders not suited to DVD.
OPTICAL IN
OPTICAL
COAXIAL
S VIDEO VIDEO
P B Y DIGITAL AUDIO OUT
(PCM/ BITSTREAM)
Insert fully with
this side up.
Amplifi er’s rear panel
Optical digital audio cable
Do not bend sharply when
connecting.
This unit’s rear panel
■ With COAXIAL
OPTICAL
COAXIAL
S VIDEO VIDEO O-L
P B Y DIGITAL
AUDIO OUT (PCM/ BITSTREAM)
COAXIAL IN
Amplifi er’s rear panel
This unit’s rear panel
Coaxial cable
Leave “Yellow” unconnected.
Con
venient
functions
DMR-XW450_GL_en.indb 95 DMR-XW450_GL_en.indb 95 2009/04/08 午前 10:06:51 2009/04/08 午前 10:06:51