PYLE Audio PICDLD82I - Manual (Page 4)

OR BACK/ TUNE - NEXT/ TUNE +
E-8 E-7
SWITCH UNIT TO "STAND-BY" MODE
PRESS & HOLD FOR 3 SECONDS
DISPLAY SHOWS HOUR OR HOUR (FLASHING)
CLOCK ADJ.
12 24
PRESS TO SELECT 12-HOUR
OR 24-HOUR CLOCK DISPLAY SYSTEM & PRESS TO CONFIRM
YOUR SELECTION
CLOCK ADJ.
PRESS REPEATEDLY TO SET
THE CORRECT IN THE DISPLAY & PRESS TO CONFIRM HOUR CLOCK ADJ.
PRESS REPEATEDLY TO SET
THE CORRECT IN THE DISPLAY & PRESS TO CONFIRM MINUTE CLOCK ADJ.
CORRECT TIME IS NOW SET & WILL BE SHOWN IN THE DISPLAY!
DIGITAL CLOCK FUNCTION
HOW TO SET CORRECT TIME:
THIS UNIT HAS A BUILT-IN DIGITAL CLOCK, WHICH IS DISPLAYED AT ALL TIMES DURING
THE UNIT BEING POWERED, OTHER THAN DURING THE FOLLOWING THREE SITUATIONS:
1) WHEN THE DIMMER FUNCTION IS ENABLED TO HAVE DISPLAY BRIGHTNESS LEVEL AT
0 (DISPLAY LIGHTS OFF/ FULL DIMMED).
2) WHEN USING THE FUNCTION KEY TO SELECT THE RADIO FM MODE, THE DISPLAY WILL
MOMENTARILY SHOW
THE FM FREQUENCY PAY BACK BEFORE RETURNING TO THE DIGITAL CLOCK.
3) WHEN USING THE NIT FUNCTIONS/ CONTROLS (I.E. VOLUME CONTROL, FM
FREQUENCY TUNING, ALARM SETTING
ETC.), THAT REQUIRE INFORMATION TO BE MOMENTARILY DISPLAYED.
TO SET THE TIME, FOLLOW THE BELOW STEPS:
*NOTE:
THAT WHEN THE DIGITAL CLOCK IS NOT SET, THE DIGITAL CLOCK DISPLAY SHALL
CONTINUOUSLY FLASH TO INDICATE THAT THE CORRECT TIME HAS NOT YET BEEN SET.
ALARM FUNCTION
ALARM TIME SETTING
- THIS SET IS EQUIPPED WITH 3 ALARM MODES: BUZZER, RADIO AND iPod.
BEFORE SETTING THE ALARM, MAKE SURE TO SET THE CLOCK.
1. AT STANDBY MODE, PRESS AND HOLD ALARM SET KEY UNTIL THE DISPLAY
HOUR FLASHING.
2. PRESS KEY TO REACH THE HOUR OF
THE DESIRED WAKE UP TIME.
3. PRESS TO CONFIRM THE UNIT SHOULD NOW HAVE THE DISPLAY
MINUTES FLASHING.
4. PRESS
ALARM SET
KEY TO REACH THE MINUTES OF
THE DESIRED WAKE UP TIME.
5. PRESS ALARM SET KEY TO COMPLETE AND CONFIRM THE ALARM TIME SETTING.
ALARM ON SETTING
ONCE THE ALARM TIME IS SET, SELECT THE SOURCE THAT YOU WISH THE UNIT
TO PLAYBACK FROM AT WAKE UP TIME:
AL = BUZZER ALARM / FM =RADIO / iPod = iPod or iPhone
1. AT STANDBY MODE, PRESS ALARM SET KEY ONCE, THE DISPLAY
WILL CHANGE FROM REAL TIME TO ALARM WAKE UP TIME THAT WAS SET.
2. PRESS ALARM SET KEY REPEATEDLY TO SELECT THE SOURCE AS DESIRED,
THE SELECTED SOURCE WILL BE INDICATED BY THE SYMBOL FLASHING,
AFTER SELECTING THE SOURCE, THE SET WILL RETURN TO STANDBY MODE
AFTER ABOUT 5 SECONDS THE AL SYMBOL WILL BE SHOWN ON THE DISPLAY
AS LONG AS THE ALARM FUNCTION IS "ACTIVE".
ALARM OFF SETTING
1. AT STANDBY MODE, PRESS ALARM SET KEY ONCE, THE DISPLAY WILL CHANGE
FROM REAL TIME TO ALARM WAKE UP TIME THAT WAS SET.
2. PRESS ALARM SET KEY REPEATEDLY TO SELECT THE AL SYMBOL,
UNTIL THE AL SYMBOL STOP FLASHING TO INDICATE "ALARM OFF",
THE SET WILL RETURN TO STANDBY MODE AFTER ABOUT 5 SECONDS,
THE AL SYMBOL WILL DISAPPEAR FROM THE DISPLAY.
ALARM MODE SETTING
1. FOR iPod/ iPhone: CONNECT THE iPod/ iPhone AS DESCRIBED. SELECT & PAUSE
PLAYBACK OF THE SONG OR DESIRED PLAYLIST TO PLAY AT THE WAKE UP TIME.
(PLAYBACK WILL AUTOMATICALLY RESUME AT ALARM TIME).
2. FOR RADIO: TUNE IN THE DESIRED STATION, PRIOR TO PLAYING THE UNIT ON
STANDBY MODE.
3. THE WAKE UP VOLUME LEVEL AUTOMATICALLY WILL RISE FROM
LEVEL 0 - 16 (MINIMUM) FOR WAKE UP VOLUME LEVEL MORE THAN 16
IT MUST BE SET BY THE USER.
4. IF THE ALARM IS SET AS WAKE TO iPod. YOU WILL NEED TO CONNECT THE iPod
PROPERLY AS DESCRIBED. OTHERWISE, THE BUZZER ALARM WILL SOUND
AT THE SET TIME IF THE iPod HAS NOT BE CONNECTED.
5. THE ALARM WAKE UP TIMER WILL AUTOMATICALLY TURN OFF AFTER
AROUND AN HOUR.
OR BACK/ TUNE - NEXT/ TUNE +
OR BACK/ TUNE - NEXT/ TUNE +
OR BACK/ TUNE - NEXT/ TUNE +
OR BACK/ TUNE - NEXT/ TUNE +