Pioneer PDP-436FDE - Manual (Page 41)

41
En
Enjoying through External Equipment 10
En
gl
is
h
Using HDMI Input
The INPUT 3 terminals include HDMI terminals to which digital
video and audio signals can be input. To use the HDMI
terminal, activate the terminal and specify the types of video
and audio signals to be received from the connected
equipment. For the types of these signals, see the operation
manual that came with the connected equipment.
Before starting the menu, press INPUT 3 on the remote control
unit or press INPUT on the Media Receiver to select INPUT 3.
For audio, the system supports the following:
• Linear PCM (STEREO 2ch)
• Sampling frequency: 32 kHz, 44.1 kHz, 48 kHz
Connecting HDMI equipment
To activate the HDMI terminal:
1
Press HOME MENU.
2
Select “Option” ( / then ENTER).
3
Select “HDMI Input” ( / then ENTER).
4
Select “Setting” ( / then ENTER).
5
Select “Enable” ( / then ENTER).
6
Press HOME MENU to exit the menu.
To specify the type of digital video signals:
1
Repeat steps 1 to 3 provided for “ To activate the HDMI
terminal”.
2
Select “Video” ( / then ENTER).
3
Select the type of digital video signals ( / then ENTER).
• If you select “Auto”, an attempt will be made to identify
the type of digital video signals when digital video
signals are received.
4
Press HOME MENU to exit the menu.
NOTE
• If you select a parameter other than “Auto”, make such a
setting that results in natural colour.
• If no image appears, specify another digital video signal type.
• For the digital video signal types to be specified, check the
operation manual that came with the connected equipment.
To specify the type of audio signals:
1
Repeat steps 1 to 3 provided for “ To activate the HDMI
terminal”.
2
Select “Audio” ( / then ENTER).
3
Select the type of audio signals ( / then ENTER).
• If you select “Auto”, an attempt will be made to identify
the type of audio signals when audio signals are
received.
4
Press HOME MENU to exit the menu.
NOTE
• If no sound is output, specify another audio signal type.
• For the audio signal types to be specified, check the
operation manual that came with the connected equipment.
• Depending on the equipment to be connected, you also need
to connect analogue audio cables.
Input signal correlation table
1920 ∗ 1080i@50Hz
720 ∗ 576p@50Hz
1280
∗
720p@50Hz
720(1440)
∗
576i@50Hz
1920 ∗ [email protected]/60Hz
720 ∗ [email protected]/60Hz
1280 ∗ [email protected]/60Hz
720(1440)
∗
[email protected]/60Hz
1920 ∗ 1080p@24Hz
ANT
INPUT 2
INPUT 1
SERVICE ONLY
INPUT
I /o link.A
SELECT
INPUT 2
INPUT 3 HDMI
SYSTEM CABLE
BLACK WHITE
COMPONENT VIDEO
2 3
Y P B P R R -AUDIO -L
AUDIO OUTPUT
Media Receiver (rear view)
SCART cable
(commercially available.)
Connect the SCART cable only
when inputting analogue audio
signals.
HDMI equipment
HDMI cable
(commercially
available.)
Item Description
Disable
(factory default) Deactivates the HDMI terminal.
Enable Activates the HDMI terminal.
Item Description
Auto
(factory default) Automatically identifies input digital video
signals.
Colour-1 Digital Component Video signals (4:2:2) locked
Colour-2 Digital Component Video signals (4:4:4) locked
Colour-3 Digital RGB signals locked
Item Description
Auto
(factory default) Automatically identifies input audio signals.
Digital Accepts digital audio signals.
Analogue Accepts analogue audio signals.
PDP-506FDE.book Page 41 Wednesday, June 29, 2005 4:00 PM