Parker Hannifin 192-510011N7 - Manual (Page 26)

Accessories for HLE and HLEZ
Automation
26 Parker Hannifin GmbH
Electromechanical Division
Clamping profile
The clamping profile is used in conjunction with the standard load attachment plate to rapidly install and fasten various combi-
nations of HAUSER linear units. Two clamping profiles are required to fasten an HLE or HLEZ to a load attachment plate. The
following table shows the profiles required for the various axis combinations:
HLE80 HLE100 / HLEZ100 HLE150 / HLEZ150
HLE80 KP70cM6 (Art.no.: 500-000904) --- ---
HLE100 / HLEZ100 KP90cM6 (Art.no.: 500-000905) KP90cM6 (Art.no.: 500-000905) ---
HLE150 / HLEZ150 KP140c2 (Art.no.: 500-000903) KP140c2 (Art.no. 500-000903) KP140c1 (Art. no.500-000902)
L
LA1 A1
A2
B1
Ø
D1
T
B
Ø
D2
D
Model / size Type A1 A2 B B1 D D1 D2 L LA1 T Art. no.
HLE80 KP70cM6 15 10 30 20 20 Ш 11 Ш 6.6 70 40± 0.2 7 500-000904
HLE100 / HLEZ100 KP90cM6 15 10 30 20 20 Ш 11 Ш 6.6 90 60± 0.2 7 500-000905
HLE150 / HLEZ150 KP140c1 25 12 40 25 30 Ш 15 Ш 9 140 90± 0.1 9 500-000902
HLE150 / HLEZ150 KP140c2 25 10 30 20 20 Ш 15 Ш 9 140 90± 0.1 9 500-000903
T-nuts and bolts
The T-nuts and bolts are used to fasten any element into the T-grooves of the profile and to the upper side of the flange plate.
l k
d e
e1
e1
e
k
h1
d a
Model / size Designation a d e e1 1h k l Art. no.
HLE80+100 / HLEZ100 Bolt DIN787 M8x8x25 -- M8 13 13 -- 6 25 131-700001
HLE80+100 / HLEZ100 Bolt DIN787 M8x8x32 -- M8 13 13 -- 6 32 131-700002
HLE80+100 / HLEZ100 Bolt DIN787 M8x8x40 -- M8 13 13 -- 6 40 131-700003
HLE150 / HLEZ150 Bolt DIN787 M10x10x25 -- M10 15 15 -- 6 25 131-700007
HLE150 / HLEZ150 Bolt DIN787 M10x10x32 -- M10 15 15 -- 6 32 131-700008
HLE150 / HLEZ150 Bolt DIN787 M10x10x40 -- M10 15 15 -- 6 40 131-700009
HLE150 / HLEZ150 Bolt DIN787 M10x10x63 -- M10 15 15 -- 6 63 131-700011
HLE80+100 / HLEZ100 Nut DIN508 M6x8 8 M6 13 13 10 6 -- 131-700103
HLE150 / HLEZ150 Nut DIN508 M8x10 10 M8 15 15 12 6 -- 131-700104
HLE80+100 / HLEZ100 Long nut* HWN313 ZN M6x8 8 M6 13 26 10 6 -- 131-700140
HLE150 / HLEZ150 Long nut* HWN313 ZN M8x10 10 M8 15 30 12 6 -- 131-700141
HLE80+100 / HLEZ100 Nut ITEM St M6 without drawing 400-000033
HLE150 / HLEZ150 Nut HWN314 ZN M8x10 Rhombus form for installation at later date 131-700155
* When using a combination of two linear axes over the clamping profile, we recommend that long nuts are used
top
bottom