Philips MX5000/37 - Manual (Page 20)

18
English
General features
Skipping to another track/chapter
● Press S or T repeatedly during playback to skip
backward or forward. Each press will take the disc to the
beginning of the previous or next track/chapter.
Note:
– If the REPEAT function has been set, pressing
S or
T will replay the same track/chapter.
To skip to the beginning of the current track/
chapter during playback
● Press S once.
To go directly to any track/chapter
● Use the numeric keypad (0-9) to enter the number of
the desired track/chapter.
Fast Search
1 Hold down
S or T about two seconds to fast
reverse or forward the disc. The available speeds are as
follows :
MP3-CD : x2 ™ x4 ™ x8 ™ x16
CD : x2 ™ x4 ™ x8
2 To resume normal play, press
£ (ÉÅ ).
Continue playback from the last stop point
1 Press Ç once will go into “Resume Stop” mode. The disc
can resume playback from the point at which it stopped
when you press
£ (ÉÅ ).
➜ “ RESUME” appears.
2 To stop playback completely, pressÇ again.
Notes:
– When the player is disconnected from the power supply or
the disc tray is opened, the resume option will be cancelled
automatically.
– The resume option may not be available on some discs.
Repeat play
For CD - Repeat track/disc(s)
1 Press REPEAT repeatedly to select the following :
➜ ∫ – to repeat playback of the current track.
➜ ∫ ALL – to repeat playback of the current disc.
➜ ∫ ALL DISC – to repeat playback of all three discs.
2 To return to normal play, press REPEAT until
∫
disappears from the display.
● For MP3-CD, it can only repeat the current track or the
album.
Notes:
– To use
∫
DISC ALL (repeat all discs), you must have a disc
in all three trays . Otherwise, it will stop when reaching an
empty tray.
– When
∫ (repeat one) is activated, you cannot skip to
another track by pressing
S or T. You must either exit
Repeat mode or use the numeric keypad to enter the desired
track number.
For DVD - Repeat chapter/title
1 Press REPEAT repeatedly during playback to select :
➜ CHAPTER REPEAT – to repeat playback of the
current chapter. CHAP icon flashes.
➜ TITLE REPEAT – to repeat playback of the current
title. TITLE icon flashes.
2 To return to normal play, press REPEAT until
“REPEAT OFF” appears.
Note:
– Repeat play might not work correctly with some DVDs.
Program favorite tracks (CD)
You can program up to 32 tracks for playback in any
desired order.
This function only operates with audio
CDs (not DVDs).
1 Load the desired discs on the disc trays (refer to “Basic
playback”).
2 Press PROGRAM.
➜ “PROG” icon start flashing.
3 Press DISC SKIP (or DVD/CD) repeatedly to select the
desired disc (if necessary).
➜ The disc number appears.
4 Use the numeric keypad (0-9) to select the desired
track number.
➜ If you attempt to program more than 32 tracks,
"
P-FULL" is displayed.
5 Press OK on the remote control to store the track.
● Repeat steps 3-5 to store other tracks.
6 To end programming, press Ç once.
➜ “PROG” icon stays and the program mode remains
active.
7 To start program play, press
£ (ÉÅ ).
Exit the program mode temporarily
● In stop mode, press Ç and followed by PROGRAM.
➜ “ P-OFF” appears.
● To return to the programming mode, press PROGRAM
again.
Reviewing the program
● Stop playback and press 3 or 4 repeatedly.
● To exit review mode, press Ç.
O
PERATIONS